본문 바로가기
Guides

What Sets CNC Machining Prices in Korea

CostCNC machiningJul 17, 2026

Price Is Fundamentally Machining Time

The reason quotes differ between shops for the same drawing is that each shop estimates a different amount of time.

CNC machining cost is the time that equipment and operators spend on the part, with material cost added on top. So the accurate statement is not "complex means expensive" but "long time means expensive."

A complex shape is cheap if it can be cut continuously in a single setup. A simple shape becomes expensive if it requires many flips and small-diameter tools.

Factors That Determine Price

1. Setup: Dominant at Small Quantities

Before cutting starts, you must fix the stock, set the origin, load the program, and verify the first article. This time is nearly constant regardless of quantity.

So ordering from 1 part gives a high per-piece price. That is because one piece bears the entire setup cost. Ordering 10 spreads the setup, and the per-piece price drops significantly.

Practical implication: Do not split an order of the same quantity. Ordering 5 pieces twice costs more than ordering 10 once, because setup occurs twice.

2. Refixturing: Number of Faces Machined

If all features can be machined in a single setup, it is cheap. Each flip adds a setup.

  • One-face machining — Plate-type parts. Lowest cost

  • Two faces — One flip

  • 5 to 6 faces — A 3-axis machine needs multiple fixturings, and alignment error accumulates with each fixturing

A 5-axis machine can machine multiple faces in a single fixturing, but machine rate and programming difficulty go up. Depending on the part, multiple 3-axis fixturings may be better, or a single 5-axis fixturing may be better.

Drawing implication: Reduce the number of faces machined. If a single hole on the back forces a flip, check whether that hole can be relocated to a position reachable from the front.

3. Cutting Time: Material and Shape

It is a function of removed volume and cutting speed. Material is a major variable.

Material

Machinability

Notes

Aluminum (6061, etc.)

Good

High-speed cutting possible, long tool life

Carbon steel (S45C (1045 carbon steel), etc.)

Average

—

Stainless steel (304/316)

Poor

Work hardening, low thermal conductivity. Low cutting speed, short tool life

Titanium, Inconel

Very poor

—

In terms of shape, deep pockets, small inside corner radii, and thin walls constrain cutting conditions.

4. Tolerance and Inspection: An Underestimated Item

Tightening tolerances triggers the following chain of effects.

  • Lower cutting speed (to limit thermal distortion and tool deflection)

  • In-process measurement inserted (machine stops, then measures)

  • Added finishing passes

  • Higher reject rate (spare parts made are reflected in the cost)

  • Inspection labor is charged separately when an inspection report is required

Applying tight tolerances to every dimension makes the price jump. The standard approach is to tighten only the features that function and leave the rest at general tolerance.

5. Finishing

Anodizing, painting, heat treatment, and surface finishing are mostly outsourced processes. They add cost, but the lead time impact is greater.

Share of Material Cost

The perception that "aluminum is cheap, so the part is cheap" is right in its conclusion but inaccurate in its reasoning.

For most CNC parts, machining cost exceeds material cost. The practical reason aluminum is cheap is not its material price but its higher cutting speed.

However, large parts are an exception. For a shape that removes only a small amount from a large block, material cost takes a bigger share. In that case, designing to optimize stock size is effective.

Why Quotes Differ Between Shops

  • Equipment owned — With 5-axis, fewer setups

  • Tool inventory — If special tools are on hand, no need to procure them

  • Main workload — With experience on similar shapes, programs and fixtures are already in place

  • Shop load — With no spare capacity, price goes up

  • Risk assessment — If the part is judged difficult, a margin is added

Even for the same drawing, results differ by shop. The role of a quote platform is this matching.

Cost Reduction Priorities

  1. Apply tolerances only to the faces that need them — Biggest effect

  2. Consolidate quantities — Avoid splitting setups

  3. Enlarge corner radii — Larger tools allow faster cutting

  4. Reduce the number of faces machined — Fewer flips

  5. Avoid deep pockets

  6. Reconsider the material — Is 316 really required, is stainless really required

  7. Reconsider finishing — If it is for appearance, consider alternatives

FAQ

Why is the quote for 1 part so high?

Because of setup cost. The per-piece price of a single prototype is inherently high. It cannot be compared directly with production pricing.

Can I get a rough quote without a drawing?

It is difficult. Even for the same size, tolerance, shape, and material can cause differences of several times. With a 3D model, an accurate calculation is possible.

What does a rush order cost?

The cost of inserting the job into the existing schedule is added. Conversely, flexible lead time becomes a negotiating point.

Summary

  • Price is a function of time, not complexity

  • Setup dominates small-quantity pricing. Consolidate quantities

  • Blanket tolerance specification is the most common cost waste

  • Material affects cost through cutting speed, more than through price

Upload a STEP file and the quote is calculated from the analyzed geometry. You can see which factors increase time.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523