본문 바로가기
Guides

H7/g6 Fit Tolerance for Pins and Bearings

TolerancesCNC machiningJul 17, 2026

H7/g6 is a sliding clearance fit that always guarantees a small gap between the hole (H7) and the shaft (g6). At Ø20, the gap is always between 7 µm minimum and 41 µm maximum. Use it where a part must slide without play, such as locating pins and slide bushings.

What Is a Fit?

In an assembly where a shaft (pin, bearing, bushing) goes into a hole, the dimensional relationship between the two parts determines function. A fit specifies the tolerance ranges of the hole and shaft as a pair, so that the intended clearance (or interference) is guaranteed when assembled. The current standard is ISO 286 (KS B ISO 286 in Korea).

The key point: If the drawing says only Ø20, both the hole and the pin are machined aiming for Ø20. The actual parts scatter within their own tolerance ranges, so the moment the hole comes out at 19.99 and the pin at 20.01, assembly is impossible. A fit turns this chance into a design.

Reading the Notation: Anatomy of "Ø20 H7/g6"

Element

Meaning

Capital letter (H)

Tolerance position of the hole. H means "the lower limit is exactly the nominal size" (never undersized)

Lowercase letter (g)

Tolerance position of the shaft. g means slightly smaller than the nominal size

Number (7, 6)

IT grade, the tolerance width. The smaller the number, the tighter the tolerance

Most practical work uses the hole-basis system. The hole is fixed at H (standardizing the side that is harder to machine and inspect), and the shaft symbol is varied to adjust clearance or interference.

Three Types of Fit: Typical Combinations and Uses

Type

Typical combination

Assembled state

Use

Clearance (loose)

H7/f7

Visible gap, free rotation

Rotating shafts, journals, parts that need lubrication

Clearance (sliding)

H7/g6

Slides without play

Locating pins, slide bushings, jig pins that must be removed

Transition (locating)

H7/h6

Smallest gap that can still be assembled by hand

Stationary locating, parts that are assembled and disassembled repeatedly

Transition

H7/k6 · H7/n6

Between clearance and light interference

Precision locating, keyed pulleys and gears

Interference (press)

H7/p6

Press-fitting required

Pressed-in bushings, pins that must not come out

Fit Table: H7 Hole and Main Shafts (unit: µm)

Hole H7 deviation (relative to nominal size: upper limit / lower limit):

Nominal diameter (mm)

H7 (hole)

g6

h6

f7

k6

n6

p6

3 ~ 6

+12 / 0

−4 / −12

0 / −8

−10 / −22

+9 / +1

+16 / +8

+20 / +12

6 ~ 10

+15 / 0

−5 / −14

0 / −9

−13 / −28

+10 / +1

+19 / +10

+24 / +15

10 ~ 18

+18 / 0

−6 / −17

0 / −11

−16 / −34

+12 / +1

+23 / +12

+29 / +18

18 ~ 30

+21 / 0

−7 / −20

0 / −13

−20 / −41

+15 / +2

+28 / +15

+35 / +22

30 ~ 50

+25 / 0

−9 / −25

0 / −16

−25 / −50

+18 / +2

+33 / +17

+42 / +26

50 ~ 80

+30 / 0

−10 / −29

0 / −19

−30 / −60

+21 / +2

+39 / +20

+51 / +32

Example: Ø20 H7/g6:

  • Hole: 20.000 ~ 20.021

  • Shaft: 19.980 ~ 19.993

  • Resulting clearance: 7 µm minimum ~ 41 µm maximum — whatever pair you pick, a sliding gap is always guaranteed

Why the Pin Won't Go In: The ±0.05 Drawing Trap

A typical path to assembly failure goes like this. The designer draws both the hole and the pin as Ø20±0.05. It looks precise, but with this tolerance the hole can legally be 19.95 and the pin 20.05. That is up to 0.1 mm of interference, and the pin will never go in. Conversely, a 20.05 hole with a 19.95 pin gives 0.1 mm of clearance, and locating becomes meaningless.

As covered in the earlier article on general tolerances (ISO 2768), the ±0.1 to 0.2 of general tolerances, and even ±0.05, is two orders of magnitude too coarse for a fit. Fits work in µm (0.001 mm), and at this scale the tolerance should be specified with the symbol system (H7/g6) rather than by "writing a narrower number," so that machining and inspection can respond with the right process.

Machining View: An H7 Hole Is Not a Drilled Hole

Specifying a fit affects price, because the process changes.

Requirement

Process

Cost impact

Standard drilled hole (Ø20, no tolerance)

One drilling pass

Baseline

H7 hole

Drilling, then boring or reaming to finish

Added process

Shaft g6/h6

Finish turning, grinding if needed

Added process and measurement

Inspection

Limit gauge or µm-class measuring instrument

Added inspection effort

The principle here is the same as for surface roughness and general tolerances: specify a fit only on the holes and shafts where it functions, and relax everything else to general tolerances. Putting H7 on a hole that only needs to let a bolt pass through is a classic waste of cost (a bolt clearance hole is usually fine as a standard drilled hole at nominal +0.5 to 1 mm).

FAQ

Why won't a Ø20 pin go into a Ø20 hole?

Because both scatter around Ø20 within their tolerance ranges. If the hole lands at its lower limit (around 19.99) and the pin at its upper limit (around 20.01), the result is interference and assembly is impossible. If you need a sliding assembly, specify a pair that always guarantees clearance, such as H7/g6.

What is the difference between H7/g6 and H7/h6?

With g6 the shaft is always smaller than nominal, so a minimum clearance is guaranteed (at least 7 µm at Ø20), and it slides smoothly. With h6 the shaft's upper limit equals the nominal size, so the clearance can approach zero. There is less play, but assembly can feel tight. As a rule of thumb, use g6 for pins that are removed often, and h6 when positional accuracy comes first.

Which fit should I use for a bearing seat?

The rule is to give the rotating ring an interference-type fit and the stationary ring a clearance-to-transition fit. For a typical small machine (rotating inner ring), a good starting point is around k6 for the shaft and around H7 for the housing. The right choice varies with load and speed, so the correct answer is to follow the recommended fit table in the bearing manufacturer's catalog.

How is an interference fit (H7/p6) assembled?

Press it in, or heat the hole side (or cool the shaft) and fit it using the difference in thermal expansion. It will not go in by hand or with a hammer, and forcing it damages the parts. Do not use it where disassembly is required.

Summary

  • A fit specifies the hole and shaft dimensions as a pair, guaranteeing clearance or interference as a design value

  • Capital letter = hole, lowercase letter = shaft, number = precision grade — in practice the hole is fixed at H (hole-basis system)

  • The three basic combinations: sliding H7/g6, locating H7/h6, press-fit H7/p6

  • Adding ±0.05 does not replace a fit — specify µm-level tolerances with symbols

  • An H7 hole is not a drilled hole but a reaming or boring process — specify it only on functional features to save cost

  • For bearings, the manufacturer's recommended table comes first

Upload a drawing and the quote shows which process each fit specification maps to.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523