본문 바로가기
Guides

How to Read Surface Roughness (Ra)

TolerancesCNC machiningFinishingJul 17, 2026

Definition of Ra

Magnified, a machined surface shows repeating fine peaks and valleys. Ra (arithmetic mean roughness) is the arithmetic mean of these irregularities relative to the center line over a sampling length. The unit is the micrometer (µm), and a smaller value means a smoother surface.

The defining formula is:

Ra = (1/L) ∫ |f(x)| dx

Here L is the sampling length and f(x) is the deviation from the center line.

Standards History — A Note on Citation

KS B 0161, widely cited in Korean literature, was withdrawn on November 25, 2014 and replaced by KS B ISO 4287. The international standard ISO 4287:1997 has likewise been replaced by ISO 21920‑2:2021. When citing a standard in a drawing or specification, confirm the current standard name.

The Limit of Ra as an Average

Ra is the average over the whole length, so a single local deep scratch is buried in the average. This is fine when the whole surface is uniform, but for surfaces where one defect decides function, Ra alone cannot judge acceptance.

For such surfaces, add Rz, a parameter based on extreme values. High-pressure sealing surfaces are the typical example.

Relationship Between Ra and Rz

In practice, the rule of thumb Rz ≈ 4×Ra is commonly used. However, this is not a conversion formula. Ra is a whole-length average and Rz is based on extreme values, so depending on the height distribution and lay direction of the surface, the actual ratio ranges from 2x to 20x. Do not use it for drawing conversion.

Standard Ra Series

Ra is selected from a standard series, not chosen arbitrarily.

… 0.1 · 0.2 · 0.4 · 0.8 · 1.6 · 3.2 · 6.3 · 12.5 · 25 · 50 …

Each step is about 2x apart (ISO 468 R10/3 series, ratio about 1.995). Writing a non-standard value such as Ra 2.0 on a drawing makes the measurement and inspection criteria ambiguous, so select from the standard series.

Old Finish Symbols (▽) Conversion

Drawings before 1999 used triangle symbols (▽) instead of Ra. This notation was withdrawn when the ISO notation was introduced in 1999, but it remains on old drawings in Korean shops and needs to be decoded.

Finish symbolEquivalent Ra (µm)Surface condition
▽25Filed, rough machined
▽▽6.3General turned or ground surface
▽▽▽1.6Finished surface with no visible tool marks
▽▽▽▽0.2High-grade polished surface

Note: This correspondence is a customary representative value, not a strict standard conversion. Some sources give ranges (e.g., ▽▽ = 3.2–6.3). When converting an old drawing to current Ra, do not conclude from the table alone; confirm the design intent.

The Process Determines Ra

Ra is not a value you improve by spending more machining time; it is a value determined by process selection. Below are representative ranges from the literature, which vary with equipment, material, and tool condition.

ProcessRepresentative Ra range (µm)
Rough machining (turning, milling)3.2 ~ 12.5
Precision machining0.8 ~ 3.2
Grinding0.4 ~ 1.6
Lapping, polishing0.1 ~ 0.4
EDM0.8 ~ 6.3
Laser-cut edge3.2 ~ 12.5

The practical lower limit of machining is roughly Ra 0.8–1.6. Some sources say 0.4 is achievable and others say 1.6 is the limit, so consult in advance when requiring this range. Anything below that presumes a separate process such as grinding or lapping.

Cost Structure — It Rises in Steps

As Ra requirements tighten, cost rises not linearly but in steps, because steps occur where the process changes.

Required RaProcess responseCost impact
3.2 ~ 6.3Met by general machiningNone
1.6Added finishing pass, lower feedMore time
0.8 or lessAdded process such as grinding — moving equipment, separate setup, lead time if outsourcedStep increase
0.1 or lessLapping, polishing, largely manual workHigh

There is also additional measurement cost. Requiring around Ra 0.4 calls for surface roughness tester measurement, and requiring a test report adds inspection labor separately.

Drawing Notes

Avoid Blanket Specification

Specifying Ra 0.8 for the whole drawing in the upper right corner makes every surface a grinding target. Most surfaces do not need that precision. The standard approach is to leave a generous general value and specify only functional surfaces individually.

Surfaces Where Ra Should Be Tightened

  • Sealing surfaces — O-ring and gasket contact surfaces. Local defects lead directly to leaks, so consider adding Rz
  • Sliding surfaces — Friction and wear conditions
  • Fits and bearing seats — If the surface deforms plastically during press fitting, tolerance control becomes meaningless
  • Fatigue-loaded surfaces — Rough tool marks act as crack initiation points

For other surfaces, a general machined surface (around Ra 3.2) is sufficient in most cases.

For Appearance, Use Finishing Instead of Ra

If appearance is the goal, tightening Ra is the least efficient means. The following finishing processes give more effect for the cost.

  • Bead blasting — Uniform matte texture, hides tool marks
  • Anodizing — Adds color and unifies the surface
  • Brushed (hairline) finish — Directional texture

Frequently Asked Questions

What happens if Ra is not specified?

The part is machined to the supplier standard (generally a machined surface around Ra 3.2). If there is no functional requirement, leaving it off is better for cost.

What is the difference between Ra 1.6 and Ra 0.8?

Numerically it is a 2x difference, but it may be the boundary where the process changes. Ra 1.6 can be met by precision machining, while from Ra 0.8 grinding is often added. The cost step occurs in this range.

Does a smaller Ra also improve dimensional tolerance?

They are separate measures. Ra specifies surface roughness and tolerance specifies dimensional accuracy. However, the process that achieves tight tolerance (grinding) also improves Ra, so the two often come together.

Does the same Ra result with different materials?

Even with the same process and conditions, it varies with material. Stainless steel tends to form a built‑up edge, so under the same conditions the surface tends to be rougher.

Summary

  • The process determines Ra. The machining lower limit is roughly 0.8–1.6
  • Cost rises in steps, with a process added around Ra 0.8
  • Avoid blanket specification and specify only functional surfaces individually
  • Ra is an average, so add Rz for surfaces where local defects matter
  • For appearance, solve it with finishing, not Ra

Upload a drawing to see which process the specified Ra presumes and how it is reflected in cost.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523