본문 바로가기
Guides

Laser vs. Waterjet by Material and Thickness

Choosing a processSheet & pipeJul 17, 2026

The difference in cutting principle

Laser is melt cutting; waterjet is erosion cutting.

A laser melts the material with focused light energy and expels the molten material with assist gas. It is fast and precise, but heat is input.

A waterjet sprays ultra-high-pressure water mixed with abrasive (garnet) and erodes mechanically. It is slow, but there is no heat effect.

Every difference that follows derives from this one point.

Process comparison

ItemLaserWaterjet
Cutting principleMelting (heat)Erosion (mechanical)
Cutting speedHighLow
CostLowHigh
PrecisionHighModerate
Kerf (cut width)NarrowWide
Heat-affected zone (HAZ)PresentNone
Thickness limitPresentRelatively generous
Non-metalsLimitedPossible (stone, glass, composites)
Highly reflective materials (copper, brass)RestrictedNo restriction
Cut-edge taperAlmost noneOccurs (wider at top, narrower at bottom)

What the heat-affected zone (HAZ) means

The area around a laser-cut edge is a region that has instantly melted and then rapidly solidified. This region has a different microstructure from the base material.

For most uses it is not a problem. It becomes a constraint under the following conditions.

  • The cut edge is used as a functional surface — the changed microstructure remains on the surface as is
  • Subsequent precision machining or welding — the hardened layer reduces tool life or affects weld quality
  • Fatigue loading — the HAZ can act as a crack initiation site
  • Heat treatment planned afterward — the response of the area with a thermal history differs
  • Thin sheet and large-area shapes — heat concentrates and distortion occurs. This is pronounced in aluminum

A waterjet is free of all of the above. Conditions where heat input is not permitted are the reason waterjet exists.

Selection criteria by material

MaterialDefault choiceNotes
Mild steel (SS400 (mild steel, similar to ASTM A36))LaserOxygen cutting handles thick plate
Stainless steel (304/316)LaserOxide-free cutting with nitrogen assist
AluminumLaserWatch for thermal distortion on thin sheet and large areas
Copper, brassConsider waterjetLaser restricted by high reflectivity and high thermal conductivity
TitaniumDepends on conditionsHeat sensitive
Thick plateWaterjetWhen laser thickness limit is exceeded
Stone, glass, compositesWaterjetLaser chars the material or cannot cut it
Laminates, sandwich materialsWaterjetLayers respond to heat differently

Waterjet constraint — taper

A waterjet stream loses energy as it passes through the thickness. So the cut edge is not vertical but V-shaped, wider at the top and narrower at the bottom. This is more pronounced the thicker the material and the faster the cutting speed. (At low speed or with soft materials, reverse taper in the opposite direction can appear.)

When precision is required, a taper-compensating head (nozzle tilt control) is applied, but this requires the equipment and reduces speed.

Also, abrasive is a consumable and makes up a considerable part of the operating cost. It is the main reason the hourly rate is high.

Laser constraints

  • Thickness limit — depends on power; beyond the limit, cutting is impossible or quality degrades
  • Highly reflective materials — for copper and brass, reflected light can damage the equipment, so orders are sometimes refused (modern fiber lasers have improved considerably)
  • Dross — solidified residue adheres to the underside. If conditions are unsuitable, a removal process is added

Cost judgment

In general, laser is cheaper than waterjet. Cutting speed is overwhelmingly higher and there are no consumables such as abrasive.

So the practical decision criterion is as follows.

"Is there a reason laser cannot handle it?" — if not, laser; if so (thickness exceeded, heat constraint, non-metal), waterjet.

Choosing waterjet because it seems like a higher-grade process creates unnecessary cost. It is a process applied when conditions demand it.

What to put on the drawing

  • State the material and thickness clearly — these two values decide most of the process
  • State the purpose of the cut edge — information such as "welding planned afterward" determines the process choice
  • Review the minimum hole diameter — holes smaller than the thickness have constraints. For fine holes, drilling may be better
  • Account for kerf — material equal to the cut width is lost. For precision fits, it must be reflected

Frequently asked questions

Can a laser-cut edge be used without post-machining?

It depends on the use. For structural use it is generally fine. For sliding or sealing surfaces, post-machining is needed.

The aluminum distorted

That is thermal distortion. Aluminum has high thermal conductivity, so heat spreads widely, and distortion is larger with thin sheet and large areas. If severe, consider waterjet.

Isn't waterjet more precise?

The opposite. Laser precision is higher. The kerf is narrow and there is almost no taper. The advantage of waterjet is not precision but the absence of heat effect.

Summary

  • Laser = melting (heat present, fast, low cost, high precision)
  • Waterjet = erosion (no heat, slow, high cost, handles thickness and non-metals)
  • The default is laser; waterjet is applied to exceptional conditions
  • The reason for choosing waterjet must be one of thickness / heat / non-metal

Tell us the material, thickness, and cut-edge purpose and we can review the appropriate process.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523