본문 바로가기
Guides

What Is MCT? CNC Milling Explained

Choosing a processCNC machiningSep 9, 2026

On the shop floor, "running it on the MCT" (MCT stands for machining center) means CNC milling. Two names for the same process make this easy to confuse. This explains what an MCT is, which geometries separate 3-axis, 4-axis, and 5-axis, and which parts are at a disadvantage when made on a machining center.

MCT Is a Machine Name, Not a Process Name

MCT stands for Machining Center. It means a CNC milling machine fitted with an automatic tool changer (ATC). With 20 to 40 tools loaded in the magazine and swapped automatically by the program, drilling, tapping, and end-milling are finished in sequence on a single workholding. The difference from a manual mill is not accuracy but the number of re-clampings. Each additional re-clamping changes the datum and accumulates tolerance.

So "MCT machining" and "CNC milling" are the same process. In the quote system, it is received as CNC machining (3-axis CNC milling).

3-Axis, 4-Axis, and 5-Axis Are Decided by Geometry

AxesMotionSuitable geometryLimit
3-axisX, Y, Z linear travelPlanes, pockets, holes, stepped shapes. Most brackets, plates, and housingsThe tool approaches only from above. Side holes and undercuts require re-clamping
4-axis (indexing)3-axis + 1 rotary axisHoles and keyways around a cylinder, 4-sided machiningNot simultaneous machining during rotation (index, then 3-axis)
5-axis3-axis + 2 rotary axes simultaneouslyImpellers, angled holes, compound curved surfaces. 5 sides in one clampingEquipment and programming cost. Overkill for simple shapes

The rule is simple. If every face can be reached by a tool coming straight down from above, it is 3-axis. A single angled hole or side pocket adds a re-clamping or moves the part to 4- or 5-axis. The actual axis-count decision is covered separately in 3-Axis vs. 3+2 vs. 5-Axis Machining.

Parts Suited and Unsuited to Machining Centers

Suited Parts

  • Angular parts in aluminum and brass: good machinability gives stable tolerance and surface
  • Hole position accuracy: holes drilled in a single clamping have high positional accuracy relative to each other
  • Low volume from 1 to dozens of pieces: with no mold, you can start from 1 piece

Unsuited Parts

  • Thin plate shapes: for a plate 3 mm thick or less with a few holes, laser cutting can be more economical
  • Deep pockets: when depth exceeds 3 times the diameter, the tool deflects and machining time can increase greatly (Why Deep Pockets Are Expensive)
  • Thin walls: walls of 1 mm or less may bend during cutting, making tolerances hard to hold
  • High volume: from a few hundred pieces, die casting and stamping often overtake on per-piece price

Appropriate Tolerance and Surface Roughness Requirements

General tolerance in CNC milling is around ±0.1 mm, and precision machining is at the ±0.05 mm level. Reamed holes and fit areas can be held tighter, but applying ±0.02 mm across the whole drawing adds secondary grinding and drives up cost. The rule is to state tolerances only where needed and leave the rest to general tolerances (ISO 2768). For surface roughness, Ra 1.6 to 3.2 on flat faces is the as-cut value, and requiring Ra 0.8 or below greatly increases finishing passes and time.

Drawing Conditions for a Fast CNC Milling Quote

  • A single STEP file carries all the geometry. Attach a 2D drawing only when there are tolerance, thread, or surface callouts
  • State the material: 6061 is the default, 7075 if strength is needed, SUS304 (304 stainless steel) for corrosive environments
  • State finishing (anodizing, heat treatment) and quantity together. Quantity moves the per-piece price the most

Frequently Asked Questions

Are MCT machining and CNC machining separate quote items?

They are the same item. At MakeIT it is received as CNC machining (3-axis CNC milling).

Can MCT machining be ordered from 1 part?

Yes. However, an order from 1 part carries the full setup and programming cost, so the per-piece price is highest. Ordering the same drawing in 5 to 10 pieces lowers the per-piece price substantially.

Do I need to specify "MCT machining" as the process name on the drawing?

Material, tolerance, surface roughness, and quantity callouts take priority over the process name. Once those four items are stated, MakeIT determines the process.

Summary

MCT is CNC milling with an automatic tool changer. If the tool can reach the geometry from above, it is 3-axis; if there is angled or side machining, it is 4- or 5-axis. Thin plates, deep pockets, and high volume are cheaper in other processes. State tolerances only where they are needed.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523