본문 바로가기
Guides

Helicoil vs. Insert Nut for Aluminum Threads

Choosing a processCNC machiningMaterialsSep 9, 2026

Tap an M4 thread in an aluminum part and loosen and tighten the bolt a few times, and the threads get pushed out. In most cases this is because the material is soft, not because of poor machining. Parts with repeated fastening need reinforced threads from the start, and there are two methods: Helicoil and insert nut. This guide covers when to use each and what to put on the drawing.

Why Tapped Aluminum Is Weak Under Repeated Fastening

Aluminum is much softer than a steel bolt. When a steel bolt is fastened into an aluminum internal thread, the aluminum always takes the load. One or two times is fine, but with repeated fastening, vibration, and over-torque combined, the threads deform plastically, the engagement becomes shallow, and clamping force is eventually lost. A tap that has been stripped once is hard to save other than by re-tapping one size larger, and sometimes the whole part is scrapped.

Helicoil: Replace the Thread with a Steel Coil

A Helicoil (wire thread insert) is a spring-shaped coil made of stainless steel. When you drill the hole with an STI tap one size larger than the original tap and wind the coil in, the surface the bolt contacts changes from aluminum to stainless steel.

  • Advantages: thin walls are acceptable (small outer diameter). Also used to repair stripped taps. The coil can be replaced and reused
  • Disadvantages: a dedicated tap and installation tool are required. After insertion, one more step is added to break off the coil end (tang)
  • Length designation: 1D, 1.5D, 2D, multiples of the thread diameter. For aluminum, 1.5D or longer is typical

Insert Nut: Install a Steel Bushing

An insert nut is a steel or brass bushing with threads or knurling on the outside. The threaded type (including key inserts) is screwed into a pilot hole one size larger, the press-in type is pressed in with an interference fit, and the heat insert is melted into plastic with heat. For metal parts, the threaded and press-in types are mainly used.

  • Advantages: stronger than a Helicoil and more resistant to vibration. Suited to places with large tensile and shear loads
  • Disadvantages: the outer diameter is large, so wall thickness is needed. Hard to use at wall edges. Once pressed in, it is hard to replace

Selection Criteria

SituationRecommendedReason
Repeated fastening (covers, access doors), thin wallHelicoilSmall outer diameter and can be restored by replacing the coil
Large clamping load, vibrating equipmentThreaded insertThe whole bushing takes the load
Repairing an already stripped tapHelicoilCan be saved with an STI tap one size larger
Plastic or 3D-printed partsHeat insertBecause there is no metal thread to begin with
Parts fastened only once or twiceNo reinforcement neededPlain tap. Just secure tap depth of 1.5D or more

How to Specify on the Drawing

  • Helicoil: standard, length, and through or blind, as in "M6 Helicoil 1.5D, through". Do not write the pilot hole diameter; the shop sets it by the STI tap standard
  • Insert: the manufacturer's part number or "M6 threaded insert, steel". State whether it is flush with the top surface after insertion
  • For both, state quantity × location. The number of holes per part is the added labor

Frequently Asked Questions

Can I order with Helicoil installation included?

Yes. If you state the standard on the drawing, STI tap machining and insert installation are completed before delivery. It is reflected as a separate line in the quote.

Can increasing tap depth replace reinforcement?

Increasing tap depth does not increase clamping force proportionally, because load concentrates on the first few threads. Reinforcing the thread material is the practical approach.

Is 7075 more durable in threads than 6061?

Its higher hardness is an advantage, but the hardness gap with a steel bolt is still large. For repeatedly fastened areas, reinforcement is recommended even on 7075.

Summary

Aluminum internal threads are more easily damaged than the steel bolt. For repeated fastening use a Helicoil (thin walls, repair, restoration); for large loads use an insert nut. On the drawing, state the standard, length, and quantity, and leave the pilot hole to the shop.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523