Hex Bolt Size Chart (M3 to M20)

There are mostly two reasons to look up bolt dimensions: whether there is room for the wrench, and how much space is needed to recess the head. Hex bolts and socket head cap screws are listed separately. Counterbore dimensions are in the Counterbore Chart.
Hex Bolt Chart
Units in mm. Head width is the across-flats distance (wrench size).
| Thread | Pitch | Head width (ISO/KS) | Head width (old standard) | Head height |
|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 5.5 | 2.0 |
| M4 | 0.7 | 7 | 7 | 2.8 |
| M5 | 0.8 | 8 | 8 | 3.5 |
| M6 | 1.0 | 10 | 10 | 4.0 |
| M8 | 1.25 | 13 | 13 | 5.3 |
| M10 | 1.5 | 16 | 17 | 6.4 |
| M12 | 1.75 | 18 | 19 | 7.5 |
| M16 | 2.0 | 24 | 24 | 10.0 |
| M20 | 2.5 | 30 | 30 | 12.5 |
For M10, M12, and M14, head width differs by 1 mm depending on the standard. The current ISO/KS main text gives 16, 18, and 21, while the old DIN 931/933 and the old KS/JIS annexes give 17, 19, and 22. Many bolts sold in Korea use the old-standard dimensions (17, 19, 22). When reflecting wrench clearance on a drawing, decide in advance which standard of bolt will be used.
Socket Head Cap Screw Chart
| Thread | Head diameter | Head height | Wrench size |
|---|---|---|---|
| M3 | 5.5 | 3 | 2.5 |
| M4 | 7 | 4 | 3 |
| M5 | 8.5 | 5 | 4 |
| M6 | 10 | 6 | 5 |
| M8 | 13 | 8 | 6 |
| M10 | 16 | 10 | 8 |
| M12 | 18 | 12 | 10 |
| M16 | 24 | 16 | 14 |
| M20 | 30 | 20 | 17 |
Head height equals the nominal thread size: for M6, the head is 6 mm. This table is the basis for setting counterbore depth to head height + 0.5.
Wrench Clearance: What Designs Often Miss
- Hex bolts: the radius the wrench needs to swing. Allow 1.5 times the head width from the bolt center to the wall
- Socket head: the wrench comes in from above, so only space above the bolt is needed. This is advantageous in tight spots
- Bolt spacing: at least head width + wrench thickness. If bolts are too close together, they can only be tightened one at a time
How to Specify Bolts on a Drawing
- On the assembly drawing, write type, designation, length, and quantity, such as "socket head cap screw M6×20, 4 pcs"
- If a strength class is needed, add 8.8, 10.9, or 12.9. Without it, general-grade (4.8 to 8.8) is procured
- Write stainless bolts as SUS304 (304 stainless steel) (A2) or SUS316 (316 stainless steel) (A4). Their strength is lower than carbon steel 8.8
- On part drawings, specify the hole (through, counterbore, thread), not the bolt
Common Mistakes
- Clearance for an M10 bolt was set on a 16 mm wrench, but an old-standard 17 mm bolt arrived: state the standard on the drawing
- Another part covers the hex-key bolt hole: it cannot be tightened in the assembly sequence. Check the sequence on the assembly drawing
- A 12.9 bolt into an aluminum internal thread: the internal thread fails before the bolt does. Consider a Helicoil or an insert
Frequently Asked Questions
Can bolts be procured together with the parts?
Yes, since they are standard parts. If you write type, designation, length, quantity, and strength class on the assembly drawing, we will carry through to assembly.
How does the head width of inch bolts differ?
A 1/4-inch bolt has a head width of 7/16 inch (11.1 mm), so a separate table is used. If you use inch bolts, you also need inch wrenches.
Can a bolt be recessed in a plate thinner than the head height?
Switch to a countersunk head. The plate thickness just needs to be at least the countersink depth.
See Also
- Counterbore Chart: Spot-Face Dimensions
- Thread Size Chart: Pitch and Minor Diameter
- Helicoil vs. Insert Nut
Once you have chosen the bolt, continue to the hole and thread.
Source standards: KS B 1002 and ISO 4014/4017 (hex bolts), KS B ISO 4762 (socket head cap screws). Old-standard head widths are based on DIN 931/933.
Have a part to machine?
Upload a drawing to see your quote.



