ISO 286 IT Grade Tolerance Chart

The h6, g6, p6, and H7 on a drawing all come from one table: the IT grade table. The grade sets the tolerance width, and the letter sets the tolerance position. The values people look up most often are collected in one place. For a conceptual explanation, see Fit Tolerances H7/g6.
IT Grade Table — Tolerance Width
Unit: µm (0.001mm). By nominal size range.
| Size range | IT6 | IT7 | IT8 | IT9 | IT11 |
|---|---|---|---|---|---|
| 3~6 | 8 | 12 | 18 | 30 | 75 |
| 6~10 | 9 | 15 | 22 | 36 | 90 |
| 10~18 | 11 | 18 | 27 | 43 | 110 |
| 18~30 | 13 | 21 | 33 | 52 | 130 |
| 30~50 | 16 | 25 | 39 | 62 | 160 |
| 50~80 | 19 | 30 | 46 | 74 | 190 |
| 80~120 | 22 | 35 | 54 | 87 | 220 |
IT6 and IT7 are precision machining, IT9 is general CNC, and IT11 is mid-level general tolerance. Even for the same IT7, the tolerance width grows as the diameter increases.
Commonly Used Tolerance Zone Values (18~30mm, 30~50mm)
| Tolerance zone | 18~30 | 30~50 | Character |
|---|---|---|---|
| H7 (hole) | 0/+21 | 0/+25 | Basic hole |
| g6 (shaft) | −7/−20 | −9/−25 | Clearance |
| h6 (shaft) | 0/−13 | 0/−16 | Sliding |
| k6 (shaft) | +2/+15 | +2/+18 | Transition, locating |
| n6 (shaft) | +15/+28 | +17/+33 | Light press |
| p6 (shaft) | +22/+35 | +26/+42 | Interference |
Unit: µm. The first value is the upper limit and the second is the lower limit. For example, a ⌀25 g6 shaft is machined to 24.980~24.993.
Fit Combination Selection Table
| Combination | Type | Used for |
|---|---|---|
| H7/g6 | Clearance | Rotating shafts, bushings, frequent disassembly |
| H7/h6 | Sliding | Locating, guiding |
| H7/k6 | Transition | Bearing inner ring, locating pins |
| H7/n6 | Light press | Torque transmission without a key (small) |
| H7/p6 | Interference | Press-fit pins, bushing retention |
Fixing the hole at H7 and changing the shaft letter is the hole-basis system. This is because a hole can only be made to a set diameter with a reamer, while a shaft can be adjusted freely on a lathe.
Where Tolerance Grade Changes Machining Cost
- IT9 or looser (around ±0.03): CNC machining as is. No added cost
- IT7 hole: Reaming or boring. One extra operation per hole
- IT6 shaft: Grinding. For heat-treated parts, grinding becomes mandatory
- IT5 or tighter: Jig grinding and lapping. For small-quantity parts, the unit price multiplies
Summary
The IT grade is the width and the letter is the position. Use H7 for holes and choose g6, h6, k6, or p6 for shafts to suit the purpose. Set grades knowing that IT7 adds an operation and IT6 means grinding.
See Also
These three pages cover where and how much tolerance to apply.
Source standards: KS B ISO 286-1 (IT grades) and 286-2 (tolerance zone values).
Have a part to machine?
Upload a drawing to see your quote.



