Keyway Size Chart for Parallel Keys

Once the shaft diameter is set, the key size and groove depth follow. What goes on the drawing is the key width, shaft keyseat depth, hub keyway depth, groove length, and tolerance. Depth and tolerance are the items most often left out.
Parallel Key and Keyway Chart
Unit: mm. Key size (width × height) and groove depth for each shaft diameter range.
| Shaft diameter | Key width × height | Shaft keyseat Depth | Hub keyway Depth |
|---|---|---|---|
| 6~8 | 2×2 | 1.2 | 1.0 |
| 8~10 | 3×3 | 1.8 | 1.4 |
| 10~12 | 4×4 | 2.5 | 1.8 |
| 12~17 | 5×5 | 3.0 | 2.3 |
| 17~22 | 6×6 | 3.5 | 2.8 |
| 22~30 | 8×7 | 4.0 | 3.3 |
| 30~38 | 10×8 | 5.0 | 3.3 |
| 38~44 | 12×8 | 5.0 | 3.3 |
| 44~50 | 14×9 | 5.5 | 3.8 |
| 50~58 | 16×10 | 6.0 | 4.3 |
| 58~65 | 18×11 | 7.0 | 4.4 |
Shaft keyseat depth is measured from the shaft outer diameter to the groove bottom, and hub keyway depth from the bore diameter to the groove bottom. On the drawing, it is easier to inspect if you write "shaft diameter − groove depth" (e.g. shaft ⌀20 → 16.5) instead of the depth.
Keyway Width Tolerance: Three Types of Fit
| Type | Shaft keyseat | Hub keyway | Use |
|---|---|---|---|
| Normal | N9 | JS9 | General power transmission |
| Loose | H9 | D10 | Disassembly, sliding |
| Tight | P9 | P9 | Reversing, shock loads |
If no tolerance is specified, it is machined as normal. Use tight when forward and reverse rotation repeat, as in a motor coupling, and loose when the hub must move along the key.
What Milling Determines
- Groove end shape: cutting with an end mill leaves a round groove end (R = key width / 2). A keyway rounded at both ends is the default; a square end requires slotting, which raises cost
- Groove length: key length + 0 to 1 mm. Fit it snugly so the key does not move in the groove
- Groove position: state the distance from the shaft end to the groove. If it is missing, the manufacturer chooses arbitrarily
- Groove bottom radius: R0.16 to 0.25 for key width 8 or less, R0.25 to 0.4 above that. A sharp corner concentrates stress and the shaft breaks right there
Common Mistakes
- Groove width differs from the standard key — A nonstandard width such as 5.5 requires a custom key. Use the values in the table
- Specifying the hub keyway as milled — A groove inside a bore is slotting or broaching. The process is different, so label it "hub keyway" explicitly
- Groove depth over 1/4 of the shaft diameter — The shaft is weakened. If you go outside the table range, consider a spline or serration
FAQ
Can the key be made together with the part?
A parallel key is a standard part, so it can be sourced and even assembled. Just write the key designation on the drawing (e.g. parallel key 6×6×20).
Can I cut a keyway in an aluminum shaft?
Yes. But aluminum groove sidewalls tend to get pressed and loosen, so use a tight tolerance or a longer key.
How much does one keyway cost?
On a turned shaft, it adds one more milling setup, so the setup cost is larger than the groove itself. Even with two grooves on the same shaft, the cost difference is small.
See Also
- Tolerance Chart Overview: IT Grades and Tolerance Zones
- Types of Heat Treatment and How to Choose
- CNC Turning Process Details
Reading shaft part drawings together with these three articles will reveal any missing items.
Source standards: KS B 1311 and JIS B 1301 (parallel keys and keyways). Shaft keyseat depth t1, hub keyway depth t2, and tolerance symbols are based on the 1996 edition.
Have a part to machine?
Upload a drawing to see your quote.



