What You Give Up with AL7075 Aluminum

The short answer
- AL7075-T6 (7075 aluminum) is among the highest-strength aluminum grades — tensile about 560 to 570MPa and yield about 480 to 500MPa, about twice AL6061 (6061 aluminum), approaching some steels.
- The price comes in every direction — harder to machine, unsuitable for welding, unsuitable for bending, lower corrosion resistance, poor anodized color, highest price.
- So 7075 is not a "good material" but a card you pull out only when strength governs the design. Everywhere else, 6061 is almost always the better answer.
Where the strength comes from — an alloy built on zinc
7075 is a 7000-series alloy that uses zinc (Zn) as its main alloying element. Precipitates formed by zinc and magnesium raise strength, and in the T6 heat-treated condition it gives mechanical properties near the upper limit of what aluminum can deliver. Its history of development as an aircraft structural material says a lot about the character of this material — it is a material for designs where strength-to-weight is the top priority and everything else is tolerated.
What you have to accept — five things to know before ordering
- 1. It is harder to machine, and costs more accordingly — its high hardness causes more tool wear and heat, and even for the same shape it is cut at lower cutting speeds than 6061. As machining time grows, so does machining cost. The material cost itself is also at the top among aluminum machining stock, so it gets expensive twice over.
- 2. Assume it cannot be used in welded structures — because of the zinc, hot cracking readily occurs during welding, so arc welding is practically not recommended. If the design involves welding, change the material or change the structure to bolted joints.
- 3. It cannot be bent or formed — 7075 in the T6 condition has low elongation and is unsuitable for cold bending. It is safest to think of it not as a sheet metal material but as exclusively for machined parts.
- 4. Corrosion resistance is poor — because of its copper content it is weaker against corrosion than 6061 and is sensitive to corrosion under stress (stress corrosion cracking). For outdoor or humid environments, design on the assumption of a surface finish.
- 5. Decorative anodizing quality is poor — because of the alloy composition, color variation and mottling occur easily. It is unfavorable for cosmetic parts, though hard anodizing for wear resistance is possible → Anodizing process details
Where 7075 is still the right answer
- Parts that must squeeze out strength within a weight limit — drone arms and frames, robot joints, lightweight structural parts. The situation where "thickening in 6061 exceeds the weight budget" is the natural home of 7075.
- Mechanical parts under cyclic load — high yield strength buys margin against plastic deformation.
- Jigs and fixtures — lighter than steel and easier to machine than steel, a practical compromise for repeatedly used tooling.
- High-performance bicycle and leisure parts — a domain where strength-to-weight is the product's value itself.
Signs you should go back to 6061
- The strength calculation has margin — 7075 has no reason to exist. The price difference buys nothing.
- Stiffness can be solved with added thickness or ribs — 6061 plus geometric reinforcement is often cheaper than 7075 with a thinner geometry. Even if the amount of cutting increases, the difference in material and machining unit price often offsets it.
- Welding or bending is in the design — as seen above, these are incompatible with 7075.
- Cosmetic anodizing quality matters — that is 6061's domain.
Common mistakes
- "Please use the strongest one" — specifying 7075 on a part with strength to spare means paying twice, in material cost and machining cost.
- Designing 7075 sheet for bending — even if the drawing arrives, it cracks when folded. Match material to process: 5052 for bent parts, 6061/7075 for machined parts.
- Combining it with welding — if a drawing shows 7075 and a weld symbol together, that drawing must be redrawn.
- Untreated outdoor use — using it untreated with the feel you have from handling 6061, corrosion comes first.
See also
- AL6061 aluminum — what 'T6' means, and the difference from AL5052
- What determines CNC machining price
- CNC 3-axis machining process details
If you get 6061 and 7075 quotes side by side for the same drawing, this article's "gets expensive twice over" shows up in numbers. Upload your drawing to MakeIT and you can compare right away by changing only the material.
Have a part to machine?
Upload a drawing to see your quote.



