본문 바로가기
Guides

SPCC, SECC, SGCC (Cold-Rolled vs. Galvanized)

MaterialsSheet & pipeMaterialsNov 9, 2026

SPCC (cold-rolled steel), SECC (electro-galvanized steel), and SGCC (hot-dip galvanized steel) are designations for cold-rolled steel sheet and for steel sheet with a zinc coating on it, and they appear often in the material field of sheet metal enclosure and bracket drawings. The three share the same cold-rolled steel base and differ only in whether zinc is applied to the surface, by what method, and how much, so which to use is decided by whether it is painted and by the service environment.

Types and standard designations

Read the designation from the front: S means steel, the second letter is the product type, the third letter is the base sheet, and the final C means commercial grade.

DesignationMeaningKS / JISSurface
SPHCHot-rolled steel sheetKS D 3501 / JIS G 3131Black scale (oxide scale), no coating
SPCCCold-rolled steel sheetKS D 3512 / JIS G 3141Smooth gray, no coating
SECCElectrogalvanized steel sheet (E = Electrolytic)KS D 3528 / JIS G 3313Thin, uniform matte zinc layer
SGCCHot-dip galvanized steel sheet (G = Galvanized)KS D 3506 / JIS G 3302Thick zinc layer, sometimes with a visible pattern (spangle)

SPCC is hot-rolled sheet that is pickled and then cold-rolled; electroplating SPCC as the base gives SECC, and dipping it in molten zinc and withdrawing it gives SGCC. SPHC is mainly used for thick sheet of roughly 3mm or more and for structural parts where black scale can remain.

Coating weight and zinc thickness

SECC indicates coating weight with a designation based on one side; E16 in JIS G 3313 is a standard 20 g/m² on one side (minimum 17 g/m²), and E8, E24, and E32 also exist. SGCC, by contrast, is indicated on a total of both sides basis; Z12 in JIS G 3302 is a minimum 120 g/m² on both sides, and Z27 is a minimum 275 g/m² on both sides.

Converting with the density of zinc (about 7.1 g/cm³), SECC E16 is about 3 μm on one side and SGCC Z27 is about 19 μm on one side, so even among zinc-coated steels the amount of zinc differs by more than a factor of six. Zinc corrodes slowly by itself in the atmosphere while protecting the base steel, so the thicker the zinc layer, the later rust appears.

Use and selection criteria

ItemSPCCSECCSGCC
Corrosion resistance unpaintedLow. May rust within days to weeksIndoor levelRelatively better outdoors and in humidity
Paint finishGood (powder coating after pretreatment)Good (smooth, uniform surface)Possible, but check pretreatment conditions; pattern may show through
AppearanceAssumes paintingUsable unpaintedIndustrial appearance
WeldingEasyZinc fumesMore zinc fumes
Material cost (relative)LowestMediumMedium
  • Powder-coated enclosures and panels: The paint film handles corrosion resistance, so SPCC is often enough; to guard against the film peeling, use SECC instead of SPCC.
  • Unpainted indoor brackets and internal parts: Use SECC, which gives a clean surface even without a painting process.
  • Outdoor, condensation, and humid environments: Use SGCC, and painting it as well lasts longer; where salt exposure is high or appearance matters, consider stainless steel (SUS430 vs SUS304).

Machining considerations

Rust on cut edges

Coated steel is coated at the coil stage and then cut, so laser-cut edges and the inside of holes are bare steel with no coating. The surrounding zinc protects part of the cut edge by sacrificial action, but with thinly coated SECC the effect is small, and in humid places rust appears first at the cut edges. So for applications where cut-edge rust is a problem, specify painting after fabrication or plating after fabrication (post-plating). At the material stage, SGCC with its thick zinc layer delays cut-edge rust, and to prevent it completely choose stainless steel. For details of the cutting process, see the laser cutting guide.

Coating cracks at bends

The outside of a bend is stretched, so fine cracks or flaking can appear in the coating, and this is relatively more visible on thick-coated SGCC. The smaller the bend radius relative to the sheet thickness, the more likely cracks are, so leave margin in the radius; for calculating bend radius and flat length, see Sheet metal flat pattern calculation and the bending guide.

Welding and zinc fumes

Welding SECC or SGCC vaporizes zinc, producing fumes and removing the coating around the weld, so touch-up painting (zinc spray, etc.) is needed on that area after welding. If there are many welded structures, it is easier to match the surface finish in one pass by making the part in SPCC and painting the whole assembly; for unpainted use, specify post-plating of the whole.

Thickness standards

Thicknesses commonly seen in domestic distribution are 0.8, 1.0, 1.2, 1.6, 2.0, 2.3, and 3.2 mm. Choosing a thickness from this list makes material supply easier; a value not on the list, such as 1.5, may be out of stock in coated steel.

Drawing and purchase order notation

  • Material field: Write the designation, thickness, and coating weight together, as in SECC t1.2 or SGCC t1.6 Z27; if the coating weight is left blank, the shop often fills it in based on stock.
  • Standard: Write KS D 3528 (SECC), KS D 3506 (SGCC), KS D 3512 (SPCC), or the corresponding JIS number.
  • Surface finishing: Write the surface finish on a separate line, such as "powder coating, color ○○" or "no post-plating", and also state whether cut-edge rust is acceptable so that the fabricator interprets it the same way.
  • Welding: If there is welding, state the weld repair method (touch-up painting, etc.).

Frequently asked questions

Can SECC be powder coated?

Yes. SECC has a smooth, uniform surface and is widely used as a paint base; agree on the degreasing and conversion coating conditions before painting with the painting shop.

Can SPCC be used without painting?

It can, but there is a risk of rust even in a dry indoor setting. With no coating, fingerprints or humidity alone can cause rust, so SECC is normally used for unpainted parts.

What is the standard for preventing rust on SGCC cut edges?

The standard is to paint or post-plate after cutting and bending. With material coating alone, the cut edge remains bare steel, so rust forms on the cut edge in humid conditions.

Summary

  • SPCC is uncoated cold-rolled steel, SECC is thin electrogalvanized steel, and SGCC is thick hot-dip galvanized steel.
  • The default choices are SPCC or SECC if painted, SECC for unpainted indoor use, and SGCC for outdoor and humid use.
  • Cut edges and welds have no zinc, so if rust is a problem, specify painting or post-plating.
  • On the drawing, write the surface finish such as painting or post-plating along with the designation, thickness, and coating weight.

To request a quote for sheet metal parts, upload STEP and DWG files to MakeIT.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523