O-Ring Groove Chart for P and G Series

O-rings are standardized, so any manufacturer's product fits as long as the groove dimensions are correct. Conversely, if the groove is wrong, compression is off and it leaks. The values to put on the drawing are three: groove width, groove depth, and groove bottom diameter. They are listed separately for the P series and G series.
P Series Groove Chart (Dynamic and Static)
Units in mm. Based on a cylindrical-surface groove.
| Size range | Cross-section diameter | Groove width | Groove depth |
|---|---|---|---|
| P3~P10 | 1.9 | 2.5 | 1.4 |
| P10A~P22 | 2.4 | 3.2 | 1.8 |
| P22A~P50 | 3.5 | 4.7 | 2.7 |
| P48A~P150 | 5.7 | 7.5 | 4.6 |
G Series Groove Chart (Static)
| Size range | Cross-section diameter | Groove width | Groove depth |
|---|---|---|---|
| G25~G145 | 3.1 | 4.1 | 2.4 |
| G150~G300 | 5.7 | 7.5 | 4.6 |
The groove depths in the tables are for static use on a cylindrical surface. For dynamic use, some manufacturers recommend 0.1–0.15mm shallower, so the catalog value takes priority. The P series is used for both dynamic parts such as pistons and rods and static parts, while the G series is for static parts only, such as flanges and covers. For the same diameter, G has a thicker cross section, so the groove is larger and there is more sealing margin.
Compression: Set by Groove Depth
| Application | Compression | Groove depth basis |
|---|---|---|
| Static sealing | 15~30% | Cross-section diameter × 0.70~0.85 |
| Dynamic (reciprocating) sealing | 10~20% | Cross-section diameter × 0.80~0.90 |
| Vacuum, low pressure | 20~30% | Cross-section diameter × 0.70~0.80 |
Low compression leaks. High compression increases friction and shortens O-ring life. The groove depths in the tables are set to fall within these ranges, so as a rule do not change the depth arbitrarily.
What Else to Put on the Drawing
- Groove surface roughness: Ra 1.6 for static, Ra 0.8 or less for dynamic. If the surface is rough, the O-ring tears
- Groove edge: C0.2~0.3 or R0.2 on the edge the O-ring passes over. If sharp, the O-ring is cut during assembly
- Groove bottom radius: 0.2~0.4. Sharp corners concentrate stress
- Groove width tolerance about +0.25/0, groove depth tolerance about +0.05/0
Common Mistakes
- Only the O-ring size is given, with no groove dimensions: the shop can fill them in from the chart, but without a dynamic/static distinction the depth cannot be determined
- Groove width narrower than the cross-section diameter: cannot be assembled. The values in the table are wider than the cross-section diameter
- Internal groove deep inside a bore: the same problem as a retaining ring groove. Check that the internal grooving tool can reach the location
Frequently Asked Questions
Are the grooves different for American AS568 O-rings?
Yes. AS568 has cross-section diameters of 1.78, 2.62, 3.53, and 5.33mm, different from P and G, and its groove standard is also separate. State on the drawing which standard's O-ring will be used.
Can a dovetail groove be used instead of a rectangular groove?
Yes. It is used where the O-ring must not fall out when the cover is opened. Machining cost rises and a dedicated milling tool is needed.
How precise is the O-ring groove machining tolerance?
Around ±0.05 on depth is sufficient. Both CNC lathes and mills machine to this tolerance.
Summary
Use the chart values as they are for groove width and depth, and compression of 15–30% for static and 10–20% for dynamic. Put roughness, edge treatment, and the dynamic/static distinction on the drawing so it comes out leak-free.
See Also
- Retaining Ring Groove Chart: For Shafts and Bores
- How to Read Surface Roughness Ra
- CNC turning process details
For drawings that include groove machining, read these three articles together.
Source standard: KS B 2799 O-ring groove design criteria. Same content as JIS B 2406. Groove widths are the standard values P 2.5, 3.2, 4.7, 7.5 and G 4.1, 7.5.
Have a part to machine?
Upload a drawing to see your quote.



