본문 바로가기
Extrusion

Extrusion

Extrusion heats an aluminum billet to over 500 degrees and pushes it with a hydraulic press through a die cut with the cross-section, producing a constant cross-section continuously. It is the most economical process for parts with a constant cross-section such as window frames, heat sinks and rails. Die cost is lower than for injection molding or die casting, but 3D parts whose shape changes along the length cannot be made, and each press run consumes at least several hundred kg of billet.

Extrusion

Basics

How it works

An aluminum billet (a cylinder of metal) is heated to over 500 degrees and pushed by a hydraulic press through a die cut with the desired cross-section, forming a continuous shape of constant cross-section.

What sets it apart

Injection molding stamps out 3D "lumps"; extrusion pulls out a 2D "cross-section" of any length. For window frames, heat sinks, rails and pipes — any long part with a constant cross-section — extrusion is the most economical way to produce in volume.

Process characteristics

✔ Excellent cost per meter — a die (dies) costs less than for injection molding or die casting (hundreds of thousands to a few million KRW), and once extrusion starts, tens of meters are produced continuously, keeping the cost per meter low.

✔ Complex cross-sections in one piece — cooling fins, grooves, rails and hollow cavities can be extruded in a single piece, which beats assembling several parts on both cost and strength.

✔ Drawbacks (fixed cross-section and minimum order quantity) — shapes whose cross-section changes along the length (for example a taper) are impossible. Each press run also consumes at least several hundred kg of billet, so a minimum order quantity (MOQ) applies.

Cost structure

Die cost (lower than injection molding) + aluminum billet material cost (tied to the price per kg) + extruder running cost by tonnage + straightening, cutting and surface finishing costs

Key cost drivers

① Solid vs hollow cross-section

A solid cross-section needs only a simple die, but a hollow cross-section such as a pipe adds a bridge and a mandrel (core) inside the die. That raises die cost 2 to 3 times and slows extrusion.

② Circumscribed circle size

The larger the circumscribed circle of the cross-section, the larger the extruder needed (for example 1,800 t vs 3,600 t). A larger circle diameter raises billet size and machine tonnage together, so running cost and material cost rise at the same time.

③ Minimum order quantity (MOQ) and loss rate

Each press run must consume a whole billet (typically 200 to 500 kg), so even a small quantity of short lengths means ordering at least several hundred kg. Leftover stock becomes an inventory burden, and the defective sections at both ends (loss) are built into the unit price.

Problem drawings (review advised)

Drawings that include 3D features

Extrusion pulls out a cross-section along a length. 3D parts whose shape changes along the length (for example a taper that narrows, or a hole partway along) cannot be made by extrusion. Such parts need separate secondary CNC machining after extrusion.

Cross-sections with asymmetric wall thickness

A cross-section whose walls differ greatly in thickness (for example 1 mm on one side and 10 mm on the other) makes the metal flow unevenly during extrusion, causing severe twist and bow. If the distortion cannot be corrected, production itself may be stopped.

Very tight straightness tolerances

Extrusions bend slightly on their own as they cool. General tolerance is about 1 to 2 mm per meter, and a straightness requirement of 0.1 mm or less needs a separate straightening (stretching) step, which raises the price sharply.

Extrusion FAQ

Q. What shapes suit extrusion?
It is the most economical choice for parts with a constant cross-section running a long length, such as window frames, heat sinks, rails and pipes. Injection molding stamps out 3D "lumps"; extrusion pulls out a 2D "cross-section" of any length.
Q. Can extrusion make 3D shapes?
No. 3D parts whose shape changes along the length (for example a taper that narrows, or a hole partway along) cannot be made by extrusion. Such parts need separate secondary CNC machining after extrusion.
Q. Why does extrusion have a minimum order quantity (MOQ)?
Each press run must consume a whole billet (typically 200 to 500 kg), so even a small quantity of short lengths means ordering at least several hundred kg. Leftover stock becomes an inventory burden.
Q. Is a hollow cross-section more expensive than a solid one?
Yes. A hollow cross-section such as a pipe adds a bridge and a mandrel (core) inside the die, which raises die cost 2 to 3 times and slows extrusion.
Q. How straight can extrusions be?
Extrusions bend slightly on their own as they cool, so general tolerance is about 1 to 2 mm per meter. A straightness requirement of 0.1 mm or less needs a separate straightening (stretching) step, which raises the price sharply.

Extrusion quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
TitleExtrusionScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-MASS-EXTRUSIONThk12RevA

Related: Mass production

Read more