Metal stamping places sheet metal between a pair of upper and lower steel dies and strikes it with tens to thousands of tons of force to blank, bend and draw parts. Progressive dies finish several operations in one pass at hundreds to thousands of strokes per minute. Die costs run from tens of millions to hundreds of millions of KRW, so it is not suited to small runs. Price is set by the scrap rate of the coil layout, the number of die stages (operations) and die maintenance cost.
Metal Stamping
Basics
How it works
Sheet metal (coil or sheet) is placed between a pair of upper and lower steel dies, and a press strikes down with tens to thousands of tons of force. The metal is cut (blanking), bent (bending) or stretched (drawing) into shape. It is a volume process for sheet metal parts.
What sets it apart
Laser cutting cuts parts out one at a time with light. Stamping works like a cookie cutter and turns out hundreds to thousands of finished parts with each stroke. From automotive body panels to electronic terminals to coins, more metal parts are made by stamping than by any other process.
Process characteristics
✔ Very fast production — high-speed presses run hundreds to thousands of strokes per minute (SPM). In a progressive die, coil stock passes through the die and several operations (blanking, bending, drawing, piercing) are completed automatically in one pass.
✔ Consistent quality with minimal finishing — the die sets the part dimensions, so quality varies very little across tens of thousands of parts. Burrs are minimal and little finishing is needed.
✔ Drawbacks (high die cost, hard to change) — progressive dies cost tens of millions to hundreds of millions of KRW, and a finished die is practically impossible to reshape. High minimum order quantities (MOQ) make it unsuitable for small runs.
Cost structure
Upfront die cost (progressive > transfer > single-hit) + sheet metal (coil) material cost (including scrap rate) + press running cost by tonnage + secondary operations (tapping, welding, plating)
Key cost drivers
① Layout and scrap rate
How parts are laid out on the coil changes the proportion of offcut (scrap) a great deal. An optimized layout is the key to saving material, and drawings with a high scrap rate sharply raise material cost.
② Number of stages
The more complex the part, the more stages (operation steps) the die needs, which directly increases die length and difficulty. Simple blanking takes 1 to 2 stages; a complex connector terminal can take 15 to 20 or more.
③ Die maintenance cost
After millions of strikes the die edges wear, and the die must be re-sharpened or key components (punch, die) replaced. The larger the production volume, the more die maintenance cost is reflected in the unit price.
Problem drawings (review advised)
Quotes for runs of a few dozen to a few hundred parts
Spread over a small run, the die cost makes each part more expensive than laser cutting. For small sheet metal runs, laser cutting plus bending is far more economical. Stamping becomes price-competitive only at volumes of several thousand to tens of thousands of parts or more.
Holes smaller than the material thickness
When the punch (the upper die edge) pierces the sheet, a hole diameter smaller than the material thickness can bend or break the punch. The minimum rule of thumb is hole diameter ≥ material thickness; drawings that do not meet it are hard to produce because of the risk of die damage.
Deep drawing designs
Deep drawing stretches sheet metal deeply, and cracks form when the material's ductility (elongation limit) is exceeded. Drawings with an excessive draw ratio (depth/diameter) need multi-stage drawing (stretching in several steps), which doubles the number of dies and the process cost.
Metal Stamping FAQ
- Q. How does metal stamping work?
- Sheet metal (coil or sheet) is placed between a pair of upper and lower steel dies, and a press strikes down with tens to thousands of tons of force to cut (blanking), bend (bending) or stretch (drawing) parts. A progressive die completes several operations in one pass as the coil moves through.
- Q. What determines stamping cost?
- The scrap rate from the part layout on the coil, the number of die stages set by part complexity (simple blanking takes 1 to 2 stages; a complex connector takes 15 to 20 or more), and die maintenance cost (replacing punches and dies) from repeated strikes.
- Q. Is stamping suitable for small runs?
- No. Spread over a small run, the die cost makes each part more expensive than laser cutting. For a few dozen to a few hundred parts, laser cutting plus bending is more economical. Stamping becomes price-competitive only at volumes of several thousand to tens of thousands of parts or more.
- Q. What is the smallest hole that can be punched in sheet metal?
- In general the hole diameter must be at least the material thickness. Smaller holes can bend or break the punch (the upper die edge) as it pierces the sheet, risking die damage.
- Q. What should I watch for in deep drawing?
- Deep drawing stretches sheet metal deeply, and cracks form when the material's ductility (elongation limit) is exceeded. An excessive draw ratio (depth/diameter) calls for multi-stage drawing, which doubles the number of dies and the process cost.
Metal Stamping quote from one drawing
Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.
Upload a drawing| TitleMetal Stamping | Scale1:4 | Unitmm | |
| FormatA4 | Date2026-03-12 | Proj. | Sheet1/1 |
| Dwg No.MAKEIT-MASS-PRESS | Thk12 | RevA | |
