본문 바로가기
Injection Molding

Injection Molding

Injection molding melts plastic resin at high temperature, injects it into a mold under high pressure, then cools and solidifies it into shape. Several cavities fill in a single cycle (one shot), so output is measured in parts per second. The upfront mold cost is large (several million to tens of millions of KRW), but the cost per part falls to tens to hundreds of KRW. Price is set by the number of cavities, the part's projected area (press tonnage) and whether undercuts are present.

Injection Molding

Basics

How it works

Plastic resin pellets are melted at high temperature, injected into a mold under high pressure, then cooled and solidified into shape. It is a mass-production process for plastic parts.

What sets it apart

CNC machines and 3D printers make parts one at a time, so output is counted in parts per hour. Injection molding forms several parts (cavities) in a single cycle, so output is counted in parts per second.

Process characteristics

✔ Fast production at low unit cost — once the mold is built, the cost per part drops to tens to hundreds of KRW, and tens of thousands to hundreds of thousands of parts can be produced quickly and consistently.

✔ Wide range of materials and colors — hundreds of resins such as ABS, PC and PP are available. Transparency and pigment color can be tuned, so parts come out with a finished-product appearance without separate painting.

✔ Drawbacks (high upfront cost, hard to change) — a mold costing several million to tens of millions of KRW must be built first, so it is not suited to small runs. Once the mold is made, design changes are very difficult and expensive.

Cost structure

Upfront mold cost + plastic resin cost + machine running cost by press tonnage (per-shot cost) + post-processing labor (gate cutting, packing)

Key cost drivers

① Number of mold cavities

A mold that yields 1 part per shot (single cavity) and one that yields 4 (4 cavities) differ greatly in upfront mold cost, but the 4-cavity mold cuts the per-part cost and time to a quarter. Choosing the cavity count for your total target volume is the key to a competitive unit price.

② Projected area and press tonnage

The larger and flatter the part, the more force the high-pressure plastic exerts to pry the mold apart. A larger press (for example 150 t to 500 t) is needed to hold it shut, so machine cost rises with part area.

③ Undercut mechanisms (slide cores)

Side holes or catches that prevent the mold from opening straight up and down require special mechanisms inside the mold (slide cores, angled ejector pins and so on) that release sideways as the mold opens. These add several million KRW to the mold cost.

Problem drawings (review advised)

Quotes for runs of a few dozen parts

The per-part price of molding is low, but spreading a 10,000,000 KRW mold over 50 parts puts each part above 200,000 KRW. Small runs do not play to the strengths of injection molding, so for 50 to 100 parts, vacuum casting or 3D printing is more economical.

Right-angle drawings with a 0-degree draft angle

To reduce friction when the solidified plastic is pushed out of the mold, walls must be slightly tapered (1 to 3 degrees). A perfectly vertical (0-degree) wall can leave the part stuck in the mold or scratch its sides, so the drawing needs revising.

Uneven wall thickness (poor coring of ribs and bosses)

Plastic shrinks as it cools. If a thick column or heavy section sits next to a thin wall, that spot cools late and sink marks (surface dents) are certain to form. Unless the designer cores out the part to a uniform wall thickness, normal mass production is not possible.

Injection Molding FAQ

Q. How does injection molding work?
Plastic resin pellets are melted at high temperature, injected into a mold under high pressure, then cooled and solidified into shape. Several cavities are filled in a single cycle (one shot), so output is measured in parts per second.
Q. What determines injection molding cost?
The number of mold cavities, the part's projected area and press tonnage, and whether slide cores are needed for undercuts. More cavities lower the cost per part but raise the upfront mold cost.
Q. Is injection molding suitable for small runs?
No. Spreading a 10,000,000 KRW mold over 50 parts puts each part above 200,000 KRW, so small runs do not play to the strengths of the process. For 50 to 100 parts, vacuum casting or 3D printing is more economical.
Q. What defects are common in molded parts?
A 0-degree draft angle can leave the part stuck in the mold or scratch its surface. Ribs and bosses of uneven thickness always produce sink marks as the part cools.
Q. What materials and colors can be used?
Hundreds of resins such as ABS, PC and PP are available for your application. Transparency and pigment color can be tuned, so parts come out with a finished-product appearance without separate painting.

Injection Molding quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
TitleInjection MoldingScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-MASS-INJECTIONThk12RevA

Related: Mass production

Read more