Choosing 5052, 6061, or 7075 Aluminum

"Make it in aluminum" is not enough to get an accurate quote. The alloy depends on whether you are bending sheet or milling a block, and a different alloy can change the machining method, finishing, and price. This page covers the three alloys and processes used for low-volume parts.
Three Alloys, Three Uses
| Alloy | Character | Suitable process | Avoid |
|---|---|---|---|
| AL5052 | Bends well with good corrosion resistance. Low strength | Laser cutting + bending (sheet metal) | Precision machining (gummy, rough surface) |
| AL6061‑T6 (6061 aluminum) | Balance of strength, machinability, and anodizing. The default for machining | CNC milling and turning, cutting thick plate | Bending (T6 risks cracking; use 5052 for bending) |
| AL7075‑T6 (7075 aluminum) | Among the highest-strength aluminum alloys (about 2x 6061) | High-strength CNC-machined parts | Bending, welding, decorative anodizing (color variation) |
Use 5052 for sheet, 6061 for blocks, and 7075 only when strength calculations show 6061 is not enough. Choosing in this order is right in most cases.
Key Points by Process
Laser Cutting
Cuts the outline and holes of 1–6T sheet. Aluminum is highly reflective, so the thicker the sheet, the rougher the cut edge, and the maximum cuttable thickness is lower than for steel. Avoid hole diameters smaller than the sheet thickness.
Bending
For 5052, the minimum bend length and inside R scale with thickness. If a hole is close to the bend line, it stretches when bent. Keep holes at least 2x the thickness from the bend line to the hole edge. The flat length is calculated with the K-factor (Sheet Metal Flat Pattern Calculation).
CNC Milling and Turning
6061 machines well and can hold tolerances down to ±0.05mm. 7075 causes more tool wear and heat, so the same shape takes longer to machine. Thin walls (1mm or less) and deep pockets (depth 3x the diameter or more) tend to be expensive in any alloy.
Finishing
- Anodizing: 6061 and 5052 finish uniformly. 7075 tends to show color variation and pinholes, so it is not recommended for decorative use. Color differs slightly from lot to lot (Anodizing Color Variation)
- Powder coating: For exterior enclosures. The coating adds thickness, so account for it in assembly tolerances
- No finish: For internal parts and prototypes. Accept fingerprints and oxidation marks
What Determines Aluminum Machining Cost
Material accounts for less of the cost than you might expect. Most of it is machining time, which is set by four factors: quantity, shape complexity, tolerance, and finishing. Quote the same drawing at 1 piece and at 10 pieces and the difference in unit price is immediately visible. The details are covered in What Determines CNC Machining Unit Price.
Frequently Asked Questions
What are the criteria for choosing an aluminum machining supplier?
Check whether they handle alloy, process, and finishing together, whether they review the drawing before production, and whether they accept small orders. MakeIT accepts 5052, 6061, and 7075 and produces from 1 piece.
What is the difference between 6061 and 6063?
6063 is an alloy for extruded profiles. For machined parts, standardizing on 6061 is better for supply and price.
Can aluminum be tapped directly?
For 1–2 fastening cycles, it is fine. For locations fastened repeatedly, reinforce with a helicoil or insert (Helicoil vs Insert Nut).
Summary
5052 for sheet, 6061 for blocks, 7075 only for high strength. Among laser cutting, bending, and CNC milling, the shape decides the process, and the price is set by machining time, not material.
Have a part to machine?
Upload a drawing to see your quote.



