본문 바로가기
Guides

Guide to Plating for Steel Parts

FinishingFinishingNov 9, 2026

Plating for steel parts is a surface finish that applies a metal or oxide coating to carbon steel parts such as S45C (1045 carbon steel) and SS400 (mild steel, similar to ASTM A36) to prevent rust and to improve wear resistance and appearance. Carbon steel rusts quickly without surface treatment, and the finish is chosen based on the required corrosion resistance and the dimensional tolerance of fits and threads. On the drawing, specify the finish type and thickness together rather than the single word "plating".

Types and characteristics

Electrogalvanizing (zinc plating)

Electrogalvanizing is the basic rust protection for steel parts; zinc corrodes before the steel does, protecting the substrate through sacrificial action. A chromate (conversion coating) is applied over it to slow white rust, the corrosion of the zinc itself, and the chromate type determines the appearance: bright (bluish), colored (yellow iridescent), or black. Thickness is specified in µm, such as 8µm or 12µm. Cost and lead-time burden are relatively small, so it is widely used for brackets, covers, and general machine parts.

Electroless nickel plating

Electroless nickel plating deposits a nickel-phosphorus alloy through a chemical reaction without using electricity. Its biggest difference from other platings is that thickness is nearly uniform at corners, inside holes, and at the bottom of grooves, regardless of current distribution. As-plated hardness is about 450 to 700HV depending on phosphorus content (higher with lower phosphorus), and heat treatment at about 400℃ can raise it to 800 to 1000HV. Higher phosphorus content improves corrosion resistance and lowers hardness; it suits parts with precision fit areas or those that need wear resistance.

Electrolytic nickel and hard chrome

Electrolytic nickel plating has good gloss and is used for cosmetic parts, but current concentrates at corners, so thickness variation is large. Hard chrome plating is used on shafts and rollers that need high hardness and low friction, and it is often built up thick and then ground to size.

Black oxide (triiron tetroxide)

Black oxide is a conversion coating that oxidizes the steel surface to form a black layer of triiron tetroxide (Fe₃O₄). The coating is thin, about 0.4 to 2.4µm (supplier data), so there is almost no dimensional change; the U.S. military specification MIL‑DTL‑13924 also requires no noticeable dimensional change after treatment. However, the coating itself offers weak rust protection, so rust-preventive oil or wax is applied with it, and it suits parts that can tolerate an oil film, such as tools, jigs, and indoor machine parts.

Hot-dip galvanizing

Hot-dip galvanizing is a batch process (ISO 1461) in which finished steel is dipped into molten zinc to form a coating, and it is thick: the mean coating thickness criterion for steel over 6mm thick is 85µm or more. It is a different process from SGCC (hot-dip galvanized steel) steel sheet, which is coated continuously at the coil stage. It is used for outdoor structures and sheet metal frames; for precision machined parts, other finishes are chosen because of the thickness and run-off.

Comparison by type

FinishCorrosion resistanceThickness and dimensional effectAppearanceHardnessRelative cost
Electrogalvanizing (trivalent chromate)MediumA few to 10-odd µm; account for it on threadsSilver-white, iridescent, blackLowLow
Electroless nickelMedium to high (by phosphorus content)Uniform at the specified valueSemi-gloss gray-whiteAbout 450 to 700HV, up to about 1000HV with heat treatmentHigh
Electrolytic nickelMediumLarge thickness variation at cornersBrightMediumMedium
Hard chromeMediumThick; ground afterwardSilver brightHighHigh
Black oxideLow (relies on rust-preventive oil)About 2.4µm or less, almost noneBlackSame as base materialLow
Hot-dip zincHigh (outdoor)Tens of µm to 85µm or moreGray matteLowMedium

Relative cost is a general tendency and changes with shape, quantity, and masking extent.

Dimensional change on fits and threads

Plating builds up on the surface, so shafts get thicker and holes get smaller; on a diameter basis, the change is 2 times the coating thickness. Adding 8µm of zinc makes a hole diameter about 16µm smaller, and since the tolerance band of an Ø20 H7 hole is 21µm, machining to the pre-plating dimension leaves the plating occupying most of the tolerance. Fit symbols are covered in Fit tolerances H7/g6.

On threads, the coating builds up on both flanks of the 60° thread form, so the effect is larger than on fits, and the pitch diameter changes by about 4 times the coating thickness. With 8µm zinc, the pitch diameter change is about 32µm, which exceeds the fundamental deviation of 26 to 28µm for a grade 6g external thread on M6 and M8 (ISO 965). So machine the thread before plating to a grade with more allowance, such as 6e or 6f, or respond as follows. Pitch and pitch diameter by designation are in the thread specification chart.

  • State dimensions before and after plating: Write on the drawing whether the tolerance applies after plating, so the manufacturer can compensate the machined dimension.
  • Masking: Exclude functional dimension areas from plating, such as internal threads and bearing seats.
  • Change the finish: Specify thin electroless nickel, which has uniform thickness, or consider black oxide, which causes almost no dimensional change.

Hexavalent chromium regulation and trivalent chromate

The older colored chromate contained hexavalent chromium, but EU RoHS limits hexavalent chromium in homogeneous materials to 0.1wt% or less, so trivalent chromium conversion coating is used on parts going into electrical and electronic products. Trivalent treatment is also widely used for other parts now; for parts where appearance matters, check the color first with a trivalent-treated sample.

Drawing and purchase order notation

For a plating instruction, state the finish type, thickness, finishing (chromate type, rust-preventive oil), and scope of application (masking) together. Examples:

  • Electrogalvanizing 8µm or more, trivalent chromate (colored), no hexavalent chromium
  • Electroless nickel plating 10µm, mask M6 internal thread
  • Black oxide followed by rust-preventive oil

When writing with a standard symbol, use the ISO 2081 format or the JIS H 8610 format: ISO is Fe/Zn8, and JIS is Ep‑Fe/Zn 8 followed by the chromate symbol. However, the meaning of chromate symbols has changed between revisions of the standards, so also write "trivalent" in words next to the symbol.

Frequently asked questions

Can hardened parts be plated?

Yes. Finish heat treatment first (see Heat treatment types and how to choose), and make plating the last process. However, high-hardness steel can suffer brittle fracture from hydrogen absorbed during electroplating, so for such parts specify post-plating baking (hydrogen embrittlement relief heat treatment, ISO 2081).

Is black oxide alone enough for outdoor use?

Black oxide alone is difficult for outdoor use. Once the oil film washes off, rust forms, so use zinc plating or paint for outdoor parts.

What happens if the plating thickness is left blank?

The manufacturer processes it to its own standard thickness. Standards differ by shop, so the same drawing can give different results; for parts with fits or threads, state the thickness.

Summary

  • The basic rust protection for ordinary steel parts is electrogalvanizing + trivalent chromate.
  • If you need uniform thickness or wear resistance, use electroless nickel; if dimensions must be preserved, use black oxide + rust-preventive oil.
  • For threads and fit areas, write the dimension basis after plating and the masking on the drawing.
  • For RoHS-regulated products, state no hexavalent chromium.

For aluminum parts, consider anodizing before plating (Aluminum surface finish types).

MakeIT takes a STEP file and the plating specification together and prices CNC machining and plating in a single quote.

Have a part to machine?

Upload a drawing to see your quote.

Sponsorship & lab support

From competition prep to research projects,
we build alongside student teams and labs.

Questions?

KakaoTalk chat
031-509-0523