Aluminum Surface Treatments Beyond Anodizing

The Short Answer
- Aluminum surface treatment is not just anodizing. Anodizing (decorative/hard), chromate, and coating (powder/liquid) each solve a different problem.
- There are three questions to ask: 1) Does it need to conduct electricity? 2) Are the dimensions sensitive? 3) Does color matter?
- If in doubt: appearance + corrosion resistance = decorative anodizing, wear resistance = hard anodizing, keeping conductivity = chromate, free choice of color or a thick protective film = powder coating.
Why Not Leave It Untreated?
Aluminum naturally forms a thin oxide film on its surface, which holds up to a degree. The problem is that this film is thin and soft. Under fingerprints, scratches, moisture, and salt, appearance and corrosion resistance quickly break down. Surface treatment engineers that film to be thicker and harder, or replaces it with a different material altogether.
Option 1: Decorative Anodizing (Type II), the Default
- What it is: a process that grows the oxide film to several to tens of µm by electrolysis. Unlike plating or painting, the surface is not "coated"; the base metal itself is converted, so there is no layer to peel off.
- What you get: corrosion resistance, scratch resistance, coloring (black, silver, etc.), and a texture that leaves no fingerprints.
- Caution: color varies between lots (even with the same color specified, it can differ subtly → Anodizing color variation). Color quality depends on the alloy: 6061 and 5052 are excellent, 7075 is at a disadvantage.
- Where it fits: exterior parts, parts that are touched, and the standard finish for general mechanical parts → Anodizing process details
Option 2: Hard Anodizing (Type III), When Fighting Wear
- What it is: the same principle with a much thicker film (tens to 100µm range). Hardness rises significantly.
- What you get: wear resistance for sliding surfaces, repeated-contact areas, and fixture surfaces.
- Caution (important): as the film gets thicker, dimensions grow. Assume about half of the film grows outward from the surface, and mask precision fit areas or compensate the machined dimensions. Color is limited to dark shades, and cost and lead time are higher than decorative anodizing.
- Where it fits: wear parts, cylinders and guides, and areas fastened repeatedly.
Option 3: Chromate (Conversion Coating), When It Must Conduct Electricity
- What it is: a process that applies a very thin protective film through a chemical reaction.
- Why it exists: an anodized film is effectively an insulator. Anodizing a part that needs grounding, an EMI shield, or an electrical contact area causes electrical problems. Chromate is nearly the only standard answer that provides corrosion resistance while keeping conductivity.
- Caution: you cannot expect wear resistance, and as an appearance finish it falls short of anodizing. It is also commonly used as the base treatment (pretreatment) for painting.
- Where it fits: grounding surfaces of electronic chassis, RF parts, and partial combinations such as "anodize everything, chromate only the grounding area".
Option 4: Powder Coating, When You Need Color and Thickness
- What it is: a coating in which powder paint is applied electrostatically and baked on. The film is thicker and more uniform than liquid paint.
- What you get: a free choice of color and gloss, a thick protective film, and economy over large areas. It is especially standard for sheet metal enclosures → Sheet metal bending process details
- Caution: paint is a "coating," so it can peel from impact or scratches, and corrosion starts from the peeled spot. Because of the film thickness, precision-dimension areas and threads need masking.
- Where it fits: equipment exterior panels, cases that need brand colors, and outdoor structures.
Anodizing vs. Plating: Two Often Confused
Searches lump them together as "anodizing plating," but the principles are entirely different. One-line rule: anodizing for aluminum, plating for iron and copper-based metals is the default.
| Anodizing | Plating | |
|---|---|---|
| Principle | Oxidizes the base metal surface to grow a film | Deposits another metal onto the surface |
| Applicable materials | Aluminum and titanium only | Most metals, such as iron, copper, and zinc |
| Peeling | Integral with the base metal, no delamination | Can delaminate if adhesion is poor |
| Color | Dye coloring (black, silver, red, etc.) | The inherent color of the plating metal (nickel, chrome, gold, etc.) |
| Electrical | Film is an insulator | Mostly conductive |
| Main use | Appearance and corrosion resistance of aluminum parts | Rust protection, decoration, and conductivity of iron-based parts |
If the part is aluminum but needs conductivity, the standard answer is not plating but chromate (Option 3 above).
Choosing with Three Questions
- 1) Does it need to conduct electricity? If so, use chromate on that surface (or mask it). Anodizing and paint are insulators.
- 2) Are the dimensions sensitive? Hard anodizing and powder coating change dimensions. For fit areas, state masking/compensation on the drawing → Fit tolerance H7/g6
- 3) Does color matter? If exact color matching is needed, use powder coating; for coloring that keeps the metallic texture, use decorative anodizing. For an appearance that cannot tolerate lot-to-lot anodizing color variation, coating is safer.
Common Mistakes
- Anodizing the grounding surface too: found after assembly as a grounding failure. State "mask/chromate this surface" on the drawing.
- Fits that don't work after hard anodizing: the result of not reflecting film growth in the tolerance. State on the drawing whether the dimension is the dimension after or before finishing.
- Expecting a good appearance from decorative anodizing on 7075: color variation and blotching occur easily. Use 6061 for appearance parts → AL7075 details
- Ordering without specifying surface treatment: "do whatever is appropriate" arrives untreated. If you state the environment (outdoor/grounding/wear), the supplier can propose the right treatment.
See Also
- Anodizing process details
- Anodizing Color: Why It Differs from Lot to Lot
- AL6061 Aluminum: When to Use It
On MakeIT, when you select the anodizing option while quoting a sheet, you can see the price including surface treatment right away. For special requirements such as grounding or wear, leave a note on the drawing.
Have a part to machine?
Upload a drawing to see your quote.



