본문 바로가기
3+2-axis CNC milling (positional 5-axis)

3+2-axis CNC milling (positional 5-axis)

3+2-axis CNC milling adds two rotary axes (A and B) to a 3-axis machine. They do not move during cutting; they only position the part (indexing) so five faces of a cube can be cut in one clamping. Position accuracy is better and lead time shorter than with 3-axis re-clamping, but free-form surfaces such as impellers, which need the rotary axes to move during cutting, cannot be made. Cost depends on the number of indexing moves and the clamping strategy, and CAM time and machine hourly rate are higher than for 3-axis.

3+2-axis CNC milling (positional 5-axis)

Basic concept

How it works

This adds two rotary axes (A and B) to a standard 3-axis machining center (X, Y, Z). The rotary axes are not controlled during cutting. Instead, the workpiece is rotated and tilted to face the next surface and locked in place (indexing), and ordinary 3-axis cutting follows. The key point is that five faces of a cube (top, front, back, left, right) can be machined in a single clamping.

Key difference

Unlike 3-axis work, there is no need to unclamp and re-clamp the part each time, so accumulated setup error shrinks and lead time gets shorter. The rotary axes do not move during cutting, so free-form surfaces such as impellers and turbine blades are out of reach. Still, machine cost and CAM difficulty are about half those of simultaneous 5-axis, which keeps multi-face machining affordable.

Machining characteristics

✔ Five faces in one clamping — The workpiece is not unclamped between faces; the rotary axes just position it for each cut. Position accuracy between faces improves to about 0.01 to 0.02 mm.

✔ Short, rigid tools — For deep features the workpiece is tilted so the tool can approach, instead of extending a long tool. A short tool cuts without vibration, improving surface finish and dimensional accuracy.

✔ Downside (no free-form surfaces) — 3D free-form surfaces (impellers, artificial joints, etc.) that need the rotary axes to move during cutting cannot be machined. Those shapes require simultaneous 5-axis.

Cost structure

Raw stock cost + CAM programming time (longer than ordinary 3-axis) + 5-axis machine hourly rate (1.5 to 2 times that of 3-axis) + number of rotary indexing moves

Key cost drivers

① Number of indexing moves and faces machined

How many times the rotary axes must turn is the key cost driver. Machining all five faces increases the number of indexing moves and the machining time. It is more efficient to group only the faces that need precision into one order.

② Clamping strategy

To machine five faces, the sixth face (usually the bottom) has to be used as the reference. A dedicated fixture must be designed, or extra holding stock must be cut away later, so the clamping strategy directly affects cost.

③ Features the rotary axes can't reach

If a deep pocket or narrow slot remains out of the tool's reach even when the workpiece is tilted, the part must be unclamped and re-set after all. The advantage of 3+2-axis disappears and cost falls back to the level of ordinary 3-axis.

Problem drawings

Drawings with free-form surfaces (attempted on 3+2-axis)

For 3D free-form surfaces such as impellers or artificial joints, where the rotary axes must move simultaneously during cutting, 3+2-axis cannot guarantee surface finish or form accuracy. Such drawings should be requested as simultaneous 5-axis machining.

Drawings specifying 5-axis without multi-face accuracy requirements

If a simple single-face job just says "5-axis machining requested", the production partner ends up tying up expensive equipment inefficiently. Choosing 3+2-axis is justified only when a position tolerance between faces (e.g., TP Ø0.02) is specified.

Deep undercuts still unreachable after rotation

A deep undercut that the tool cannot reach even with the workpiece tilted 90 degrees cannot be machined on 3+2-axis either. Move to simultaneous 5-axis or split the part in the design.

3+2-axis CNC milling (positional 5-axis) FAQ

Q. What is the difference between 3+2-axis and simultaneous 5-axis CNC milling?
In 3+2-axis, the rotary axes (A and B) do not move during cutting; the part is rotated and locked (indexed) to the next face before ordinary 3-axis cutting. 3D free-form surfaces such as impellers or artificial joints, which need the rotary axes to move during cutting, cannot be made on 3+2-axis and require simultaneous 5-axis.
Q. What are the advantages of 3+2-axis CNC milling?
Five faces of a cube (top, front, back, left, right) can be machined in a single clamping, so there is no need to unclamp and re-clamp the part each time as with 3-axis. This reduces accumulated setup error (position accuracy between faces of about 0.01 to 0.02 mm) and shortens lead time.
Q. What determines the cost of 3+2-axis CNC milling?
The key is how many times the rotary axes must turn (number of indexing moves and faces machined). Machining all five faces increases indexing and time, and the clamping strategy for referencing the sixth face (usually the bottom), such as fixture design and holding stock, also affects cost.
Q. What shapes can't be machined on a 3+2-axis machine?
Deep pockets, narrow slots and deep undercuts that the tool cannot reach even with the workpiece tilted must be unclamped and re-set, which erases the advantage of 3+2-axis. Free-form surfaces such as impellers, and deep undercuts still unreachable after rotation, require simultaneous 5-axis machining or a split design.
Q. Why is 3+2-axis cheaper than simultaneous 5-axis?
The rotary axes do not move during cutting, so machine cost and CAM difficulty are about half those of simultaneous 5-axis. However, CAM programming takes longer than for 3-axis, and the machine hourly rate is 1.5 to 2 times higher.

3+2-axis CNC milling quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
Title3+2-axis CNC millingScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-CNC-3PLUS2AXISThk12RevA

Related: CNC machining

CNC machining services

Read more