본문 바로가기
EDM (electrical discharge machining)

EDM (electrical discharge machining)

EDM (sinker EDM) is a non-contact method in which an electrode (copper or graphite) made in the inverse of the desired shape is brought close to the workpiece and electric sparks melt material away in minute amounts. It can machine any electrically conductive metal regardless of hardness and produces perfect inside right-angle corners that a machining center cannot, but it is tens to hundreds of times slower than a machining center and electrode making makes up a large part of the cost.

EDM (electrical discharge machining)

Basic concept

How it works

First an electrode (usually copper or graphite) in the inverse of the desired shape is cut on a machining center. When this electrode is brought very close to the metal workpiece, an electric spark (discharge) occurs in the tiny gap between them (the spark gap) and melts the material away in minute amounts. The shape is transferred as if pressing a stamp (the electrode) into the part.

Key difference

Unlike milling, where a tool physically "cuts" the material, EDM "melts it away" with electric sparks, so the tool (electrode) never touches the workpiece. This means any electrically conductive metal can be machined regardless of hardness.

Machining characteristics

✔ Overcoming hardness — Hard materials that are difficult for milling tools, such as cemented carbide, mold steel and tungsten carbide heat-treated to HRC 60 or higher, can be handled by electrical discharge machining.

✔ Perfectly sharp inside corners — It produces perfect right-angle (R=0) corners inside pockets (slots), which the round end mill of a machining center can never make. This is essential for the ribs and bosses of injection molds.

✔ Downside (very slow) — Each electric spark melts away a tiny amount of material, so machining speed is tens to hundreds of times slower than on a machining center. It is unsuited to large-area machining.

Cost structure

Electrode making cost (CNC milling + electrode material) + machine run time (discharge time) + replacement / re-machining cost due to electrode wear

Key cost drivers

① Machining time (discharge time)

In EDM, machining time translates directly into cost. The larger the volume to remove and the smoother the surface finish required, the more discharge time grows exponentially and the more the price rises sharply.

② Electrode making cost

The electrode itself must be precisely cut on a machining center before EDM. The more complex the shape, the more electrode making time and cost increase, and this makes up a large part of an EDM quote.

③ Electrode wear

During discharge machining the electrode itself also melts and wears down little by little. In precision mold work, worn electrodes must be replaced or re-cut, so materials with a high electrode wear rate add cost.

Problem drawings

Non-conductive materials (ceramic, plastic)

EDM uses the principle of electrical discharge, so materials that do not conduct electricity (ceramic, plastic, etc.) cannot be machined. For non-conductive materials, consider processes other than EDM.

Simple square pockets a machining center can cut just fine

A drawing that asks for an entire simple square pocket to be EDM-cut just for the "sharp corners" when EDM isn't otherwise needed. It is more cost-efficient to machine most of it on a machining center and finish only the corners with EDM.

Ultra-deep holes / pockets

For very deep features, circulating the dielectric fluid becomes difficult, and as the electrode gets longer, discharge stability falls sharply. Machining time grows astronomically and the price explodes.

EDM (electrical discharge machining) FAQ

Q. What materials can EDM be used on?
Any electrically conductive metal. Hard materials that are difficult for milling tools, such as cemented carbide, mold steel and tungsten carbide heat-treated to HRC 60 or higher, can also be handled by electrical discharge. Non-conductive materials such as ceramic and plastic, however, cannot be machined.
Q. Why is EDM needed? Can't a machining center do it?
The round end mill of a machining center cannot make perfect right-angle (R=0) corners inside a pocket, but EDM can. It is essential where perfectly sharp corners are needed, such as the ribs and bosses of injection molds.
Q. What determines the cost of EDM?
Machining time (discharge time) translates directly into cost. The larger the volume to remove and the smoother the surface finish required, the more discharge time grows exponentially. Electrode making cost and the cost of replacing or re-machining worn electrodes are added on top.
Q. Why is EDM slow?
Each electric spark melts away a tiny amount of material, so machining speed is tens to hundreds of times slower than on a machining center. This makes it unsuited to large-area machining, and the deeper the feature, as with ultra-deep holes or pockets, the more machining time grows astronomically.
Q. Do simple square pockets need to be EDM-cut?
No. Asking for an entire simple square pocket to be EDM-cut just for the "sharp corners" when EDM isn't otherwise needed is inefficient. It is more cost-efficient to machine most of it on a machining center and finish only the corners with EDM.

EDM quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
TitleEDMScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-CNC-EDMThk12RevA

Related: CNC machining

CNC machining services

Read more