Wire EDM passes electricity through a thin brass wire 0.1 to 0.3 mm in diameter and cuts the 2D profile of metal precisely, like a fret saw. Gears and mold components are machined to ultra-precise tolerances of about 0.005 mm with no burrs. Because it cuts through the material from top to bottom, blind pockets and 3D curved surfaces cannot be machined, and cost depends on cutting path length, the number of start holes and the number of skim cuts.
Wire EDM
Basic concept
How it works
Electricity is passed through a brass wire thinner than a hair (usually 0.1 to 0.3 mm in diameter), and the metal is melted and cut precisely like a fret saw along a computer-controlled path. The wire is fed in one direction from the upper spool to the lower spool and is used once and discarded.
Key difference
Where sinker EDM "presses in" the shape of an electrode (stamp), wire EDM cuts out a "2D cross-section", like a fret saw following a line. No electrode needs to be made separately, so preparation cost is lower than for sinker EDM.
Machining characteristics
✔ Ultra-precise 2D profiles (0.005 mm tolerance) — Complex 2D profiles such as gears, mold components and precision jigs are machined to ultra-precise tolerances of about 0.005 mm. It can also cut heat-treated cemented carbide of HRC 60 or higher.
✔ Zero burrs, zero residual stress — Non-contact machining leaves no burrs on the cut surface, and no mechanical stress is applied to the material, so there is no thermal distortion or warping.
✔ Downside (speed and shape limits) — The wire cuts through the material from top to bottom, so blind pockets and 3D curved surfaces are physically impossible. Machining speed is also much slower than on a machining center.
Cost structure
Machine run time (cutting time) + start hole machining cost + wire consumables + finishing (2nd and 3rd skim cut) cost by precision grade
Key cost drivers
① Machining time (cutting path length)
In wire EDM too, time is money. The longer the total contour to be cut and the thicker the material, the more machining time increases in proportion.
② Number of start holes
The wire must pass through the material before cutting can begin, so a separate hole (start hole) must be drilled inside the material first. The more closed shapes (internal contours), the more start hole machining cost is added.
③ Wire consumption and number of skim cuts
The wire is a consumable used once and discarded, and a better surface finish requires 2nd and 3rd skim cuts after the first cut. The more skim cuts, the more wire consumption and machining time increase together.
Problem drawings
Blind shapes
The wire cuts by passing through the material from top to bottom, so shapes that do not go all the way through (grooves, pockets, etc.) cannot be machined by wire EDM. Sinker EDM or CNC milling suits these shapes.
3D curved surfaces (free-form surfaces)
Wire EDM is fundamentally a process that cuts out a "2D cross-section". Surfaces twisted in three dimensions, such as impellers or turbine blades, cannot be made by wire EDM. (Some machines have a taper function, but it is limited to simple angled cuts.)
Very thin sheet (0.5 mm or less)
If the material is too thin, discharge heat can warp it or the wire can push it away, greatly reducing cutting accuracy. A minimum thickness of 1 mm or more is recommended.
Wire EDM (wire electrical discharge machining) FAQ
- Q. What is the difference between wire EDM and sinker EDM?
- Sinker EDM transfers the shape of an electrode (stamp) as if pressing it in, while wire EDM cuts out a "2D cross-section", like a fret saw following a line. Wire EDM needs no separately made electrode, so preparation cost is lower than for sinker EDM.
- Q. What shapes can't be made by wire EDM?
- The wire cuts through the material from top to bottom, so blind shapes that do not go all the way through (grooves, pockets) cannot be machined. Free-form surfaces twisted in three dimensions, such as impellers or turbine blades, cannot be made either.
- Q. What determines the cost of wire EDM?
- The longer the total contour to be cut and the thicker the material, the more machining time and cost rise. The number of start holes needed for each closed shape inside the material and the number of 2nd and 3rd skim cuts for surface finish also affect cost.
- Q. How precise is wire EDM?
- It can machine complex 2D profiles to ultra-precise tolerances of about 0.005 mm. It is non-contact machining, so no burrs occur on the cut surface and no mechanical stress is applied to the material, so there is no thermal distortion or warping either.
- Q. Can very thin sheet be machined by wire EDM?
- If the material is too thin, discharge heat can warp it or the wire can push it away, greatly reducing cutting accuracy. A minimum thickness of 1 mm or more is recommended, and accuracy is hard to secure at 0.5 mm or less.
Wire EDM quote from one drawing
Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.
Upload a drawing| TitleWire EDM | Scale1:4 | Unitmm | |
| FormatA4 | Date2026-03-12 | Proj. | Sheet1/1 |
| Dwg No.MAKEIT-CNC-WIRE-EDM | Thk12 | RevA | |
Related: CNC machining
CNC machining services3-axis CNC milling
X-Y-Z 3-axis cutting. Faces, pockets, through holes on the most common machining center
3+2-axis CNC milling
positional 5-axis
Indexed 2 axes for 5-face work, not simultaneous
5-axis CNC milling
simultaneous
3 linear + 2 rotary axes. Impellers, blades
Manual milling
Manual feed. Faces, slots, one-offs
CNC turning
Round parts. OD, bores and threads by NC
Manual turning
Manual turning. One-offs and repairs
