본문 바로가기
Tube laser

Tube laser

Pipe laser cutting holds the pipe in a chuck and rotates it while a laser head cuts, perforates and chamfers in one pass. Pipes can be designed to interlock with tabs and slots, which removes the need for welding jigs. Price is set by material lost in the chucking dead zone, number of piercings and shape complexity (rotation time).

Process types

Standard tube cutting

Cutting and perforating the most common round, square and rectangular tubes

Open profile and structural shape cutting (3D laser)

Special machining that trims complex open-section structures such as L (angle), U (channel) and H-beam with a multi-axis head

Standard pipe laser cutting (fiber pipe laser)

Basic concept

How it works

Instead of working on flat plate, a long pipe is held in the machine's chuck (clamping device) and rotated while the laser head above pierces holes or cuts three-dimensional shapes.

Key difference

Pipe work used to need three steps: ① saw cutting, ② drilling and ③ milling slots. A pipe laser does all of this in one pass on a single machine.

Process characteristics

✔ A revolution in assembly (welding) - tabs and slots on pipe ends let pipes snap together like Lego blocks or a woodworking mortise and tenon. No temporary jig is needed to set angles when welding.

✔ Fast and highly accurate - there is no rough burr from sawing, so no finishing is needed, and angled (mitered) cuts can also be made precisely.

✔ Drawbacks (thickness and size limits) - the pipe outer diameter the chuck can grip (usually up to 150 to 220 mm) and the weight are limited.

Cost structure

Pipe material cost (including stock-length scrap) + number of piercings

Key cost drivers

① Chucking dead zone

Pipe usually arrives as 6-meter stock lengths. Because the machine must grip and rotate the pipe end, the last 150 to 200 mm cannot be cut and always becomes scrap (loss). This discarded portion is also built into the material cost.

② Number of piercings (holes)

As with sheet laser cutting, piercing a hole in the middle of the pipe takes the longest. Many holes, like a honeycomb, sharply raise the machining cost.

③ Shape complexity (rotation time)

Complex curves that need the pipe to be rotated back and forth take much longer than straight cuts.

Problem drawings

A 2D flat drawing saying "wrap this around a pipe"

A pipe is a three-dimensional shape, so a 2D flat pattern alone is hard to machine. The operator must rebuild the pipe shape in 3D software before CAM, so please always provide a 3D STEP file.

Assembly tolerances that are too tight

When designing Lego-style tabs, if you ignore the laser kerf and the pipe's own bow and variation and design with no gap at all (0.01mm), assembly is difficult and rework on site is needed.

Pipes too small or too large for the machine to grip

Pipes with an outer diameter of 10 mm or less, or very heavy pipes, cannot be machined without dedicated equipment.

Tube laser FAQ

Q. How does pipe laser cutting differ from conventional methods?
Conventionally three steps were needed: saw cutting, drilling and milling slots. A pipe laser holds the pipe in a chuck and rotates it, doing all of this in one pass on a single machine.
Q. What determines the price of pipe laser cutting?
Pipe usually arrives as 6-meter stock, and the 150 to 200 mm at the end that the chuck must grip cannot be cut and is lost, which is reflected in material cost. More holes (piercings), or complex curves that need more rotation, increase machining time and price.
Q. Can pipes be assembled without welding?
Tabs and slots on the pipe ends let pipes snap together like Lego blocks or a woodworking mortise and tenon, so no temporary jig is needed to set angles when welding.
Q. What file format should I provide for a pipe machining request?
A pipe is a three-dimensional shape, so a 2D flat drawing alone is hard to machine. The operator must rebuild the pipe shape in 3D software before CAM, so a 3D STEP file is required.
Q. Is there a limit on the pipe size that can be machined?
The outer diameter the machine's chuck can grip (usually up to 150 to 220 mm) and the weight are limited. Pipes with an outer diameter of 10 mm or less, or very heavy pipes, cannot be machined without dedicated equipment.

Tube laser quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
TitleTube laserScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-PIPE-LASERThk12RevA

Related: Sheet fabrication

Sheet fabrication services

Read more