본문 바로가기
Waterjet cutting

Waterjet cutting

Waterjet cutting is a cold cutting process that erodes material with high-pressure water of thousands of bar mixed with garnet abrasive. With no heat-affected zone (HAZ), it can cut thick material, from metals to glass and composites, though it is slow. Price is set by quality grade (Q1 to Q5), material hardness and thickness, and abrasive consumption.

Basic concept

How it works

Water pressurized to thousands of bar is sprayed through a fine nozzle together with garnet, a hard sand, which erodes the material at high speed to cut it.

Key difference

Unlike laser or wire EDM, it uses neither heat nor electricity, so it is a cold cutting process.

Process characteristics

✔ Almost any material

It can cut most materials: metals (steel, aluminum, titanium) as well as glass, marble, carbon fiber (CFRP) and composites.

✔ No thermal distortion (zero HAZ)

There is no heat-affected zone (HAZ, where heat burns or hardens the surrounding material), the biggest drawback of laser cutting. This is essential for aerospace and medical parts.

✔ Thick material

It can also cut thick material of 50T to 200T or more, which is hard to cut with a laser.

✔ Drawbacks

It is slower than laser, and the water stream spreads as it cuts, leaving a slight V-shaped taper on the cut face.

Key cost drivers

① Quality grade (Q1 to Q5)

Waterjet lets you adjust the roughness (quality) of the cut face.

Q1 (separation cut): when a rough edge is acceptable → the fastest and cheapest.

Q5 (very fine): when the edge must be smooth → cutting speed must be greatly reduced, so the price rises 3 to 5 times.

② Material hardness and thickness

Aluminum cuts quickly, but titanium or bulletproof glass takes much longer.

③ Abrasive consumption

Sand (garnet) is a costly consumable. The thicker and harder the material, the more sand is used, so the price goes up.

Problem drawings

Sharp internal corners required

Because the water stream has a width (kerf, about 1 to 1.5 mm), a sharp internal right angle is impossible and a radius (R) always remains.

Overly tight tolerances

There is no distortion because it is a cold process, but the dimensions at the top and bottom differ slightly due to the nature of the water stream. Precise assembly holes should not be made by waterjet and should be finished by CNC.

No quality grade specified

If the drawing does not state the edge quality grade (Q1 to Q5), a quote is hard to produce, so please include the required quality grade.

Materials that must not get wet

Materials that absorb water, such as plywood, paper and foam, cannot be cut by waterjet.

Waterjet cutting FAQ

Q. How does waterjet cutting work, and how does it differ from laser?
It is a cold cutting process that sprays water pressurized to thousands of bar together with garnet, a hard sand, to erode and cut the material. Unlike laser or wire EDM, it uses neither heat nor electricity, so there is no heat-affected zone (HAZ) at all.
Q. What determines the price of waterjet cutting?
The key factor is the quality grade (Q1 to Q5), which controls edge roughness. Q5 (very fine) requires a much lower cutting speed, so the price rises 3 to 5 times. Material hardness and thickness, and the amount of garnet (abrasive) consumed, also affect price.
Q. Can waterjet cut sharp internal right angles?
Because the water stream has a width (kerf, about 1 to 1.5 mm), a sharp internal right angle is impossible and a radius (R) always remains.
Q. Can waterjet make precise assembly holes?
There is no distortion because it is a cold process, but the dimensions at the top and bottom differ slightly due to the nature of the water stream. Do not make precise assembly holes by waterjet; finish them by CNC.
Q. Are there materials that waterjet cannot cut?
Materials that absorb water, such as plywood, paper and foam, cannot be cut by waterjet. On the other hand, it can cut most materials, including metals (steel, aluminum, titanium), glass, marble and carbon fiber (CFRP).

Waterjet cutting quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
TitleWaterjet cuttingScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-WATERJET-CUTTINGThk12RevA

Related: Sheet fabrication

Sheet fabrication services

Read more