본문 바로가기
Router

Router

Router machining is a physical cutting process in which a rotating cutting tool (bit) moves over a flat table to cut or pocket non-metal sheet such as wood, acrylic and plastic. It does not burn the material, so it suits materials that would char under a laser. Price is set by machining depth, number of tool (bit) changes and material strength.

Process types

2D flatbed router (3-axis flatbed)

The most common method, cutting out or shallow-pocketing wood, acrylic, Foamex and similar sheet (signs, furniture, interior accessories)

Multi-axis router (4 to 5 axis)

Carves three-dimensional forms, complex furniture legs, large foam mock-ups and similar from multiple angles

Standard sheet router machining (3-axis CNC router)

Basic concept

How it works

A machine with a cutting tool (router bit) spinning at very high speed moves over a wide flat table, carving and cutting the material to the drawing.

Key difference

It resembles laser in cutting sheet, but it removes material with a physical blade (bit) rather than burning it with heat. It is therefore mainly used for non-metal materials that must not burn.

Process characteristics

✔ The champion of non-metal sheet

It cuts cleanly materials such as wood, acrylic, plastic and foam that would char black or give off toxic fumes under a laser. (Soft metals such as aluminum can also be machined.)

✔ Cutting and pocketing (stepped machining) in one process

Besides cutting all the way through, it can engrave letters or machine pockets that remove only part of the thickness.

✔ Drawback (no sharp internal corners)

Because a round cutting tool rotates as it cuts, even a square hole leaves internal corners rounded to the tool radius (R).

Cost structure

Material cost

Tool (bit) wear and replacement cost + setup cost

Key cost drivers

① Machining depth and thickness

To avoid breaking the bit, thick material is not cut deep in one pass but removed in several thin layers. The deeper the cut, the more passes it takes, so it takes longer.

② Number of tool changes

The more tool types a drawing needs, such as a thick bit for fast roughing of large areas, a thin bit for precise corner finishing and a drilling bit, the more tool-change time is added and the higher the price.

③ Material strength

Soft sponge-like foam and hard hardwood (oak and so on) have very different feed rates, so the price difference is large.

Problem drawings

Drawings with perfectly square internal corners (R=0)

This is the biggest cause of router defects. Because a round bit passes through, corners stay rounded, and a square part is hard to fit into them. (A dog-bone design that gives the corner relief space is needed.)

Details that are too small or thin

Holes or sharp designs smaller than the thin router bit (usually 1 to 3 mm diameter) cannot be cut because the bit cannot enter.

Drawings with 2D lines only and no depth

The shop has to check each time: "Is this circle a through hole, or a 5 mm deep pocket?"

Router FAQ

Q. What materials is router machining suited to?
It is mainly used for non-metal materials such as wood, acrylic, plastic and foam that would char black or give off toxic fumes under a laser. It removes material with a physical blade (bit), and soft metals such as aluminum can also be machined.
Q. Can a router cut and pocket at the same time?
Besides cutting all the way through, it can engrave letters or machine pockets that remove only part of the thickness.
Q. What determines the price of router machining?
Thick material must be removed in several thin layers, so the deeper the cut, the higher the price. The price also rises when a drawing needs many tool (bit) types and so more tool changes, or when the material is stronger (such as hardwood).
Q. Can a router make perfectly square corners?
Because a round cutting tool rotates as it cuts, even a square hole leaves internal corners rounded to the tool radius (R). If perfectly square corners are needed, switch to a dog-bone design that gives the corner relief space.
Q. What should I watch for in a router drawing?
Holes or sharp designs smaller than the thin router bit (usually 1 to 3 mm diameter) cannot be cut because the bit cannot enter. Also, if there are only 2D lines and no depth, the shop must check each time whether it is a through hole or a pocket.

Router quote from one drawing

Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.

Upload a drawing
TitleRouterScale1:4Unitmm
FormatA4Date2026-03-12Proj.Sheet1/1
Dwg No.MAKEIT-ROUTERThk12RevA

Related: Sheet fabrication

Sheet fabrication services

Read more