Plasma cutting blows a very hot plasma beam made by an electric arc to melt and cut conductive metal. It cuts plate of 15T to 50T or more quickly and the equipment is very cost-effective, but cut-face quality (taper, dross) is below laser. Price is set by thickness competitiveness, slag-removal finishing cost and the limits of hole cutting.
Process types
Standard plasma
Cuts quickly using compressed air or oxygen (best value, somewhat lower precision)
High-definition plasma (HD plasma)
Uses special gases and precise control to achieve cut-face quality close to laser (can replace laser on thick plate)
3D bevel plasma
The torch (head) tilts to cut the plate edge at an angle in a V or Y shape (essential for weld joint preparation before welding)
Standard / high-definition plasma cutting
Basic concept
How it works
A strong electric arc applied to a gas turns it into plasma, the fourth state of matter, at over 20,000 degrees Celsius. This high-temperature plasma beam is blown out of a nozzle at supersonic speed to melt the metal and blow it away.
Requirement
Electricity must flow for the process to work, so it applies only to conductive metals (steel, stainless steel, aluminum and so on). It cannot cut wood or plastic.
Process characteristics
✔ Strong on thick steel plate - it cuts plate of 15T to 50T or more, which is hard for a laser, at high speed.
✔ Excellent value - equipment and upkeep costs are far lower than laser or waterjet, so it has the lowest price for large structural parts where precision matters little.
✔ Drawbacks (cut quality) - the kerf is wider than laser, and the cut face tilts slightly into a V-shaped taper. A lot of dross (slag), molten metal that hardens and hangs on the bottom, also forms.
Cost structure
Material cost
Consumables (nozzles and electrodes wear out very quickly)
Finishing labor (slag removal / grinding)
Key cost drivers
① Thickness competitiveness
On thin plate of 10T or less, laser is faster and cleaner, so laser has the better price. Once thickness passes 20T, however, plasma becomes much more cost-competitive.
② Slag (dross) removal cost
After plasma cutting, hardened molten metal on the bottom must be removed with a grinder or similar. This finishing labor is included in the quote.
③ Limits of hole cutting
Holes smaller than the plate thickness are difficult to cut. Forcing them can distort the surrounding area, so more small holes means a higher defect rate and a higher price.
Problem drawings
Tight tolerance requirements
Precision assembly tolerances such as ±0.1mm are never possible with plasma. A margin of about ±1 to 2 mm is usually needed.
Holes much smaller than the thickness
Shops are reluctant when asked to plasma-cut a 10 mm diameter bolt hole in 30T plate. (In that case, only the center point is marked and the hole is drilled later.)
Intricate, fine artwork
Designs with many narrow gaps, such as signs or decorative panels, get melted together by the wide plasma flame.
Non-metal material drawings
Non-conductive materials such as acrylic or wood cannot be plasma cut.
Plasma Cutting FAQ
- Q. How does plasma cutting work?
- A strong electric arc applied to a gas creates plasma at over 20,000 degrees Celsius, and this hot beam is blown out at supersonic speed to melt the metal and blow it away. Electricity must flow, so it applies only to conductive metals such as steel, stainless steel and aluminum, and it cannot cut wood or plastic.
- Q. Which is better, plasma or laser?
- On thin plate of 10T or less, laser is faster and cleaner and has the better price, but above 20T plasma becomes much more cost-competitive. Plasma is especially strong on plate of 15T to 50T or more.
- Q. Is extra work needed after plasma cutting?
- After cutting, molten metal residue (dross, slag) hardens on the bottom and must be removed with a grinder or similar. This labor is included in the quote.
- Q. Can I require tight tolerances from plasma cutting?
- Precision assembly tolerances such as ±0.1mm are never possible, and a margin of about ±1 to 2 mm is usually needed. This is because the kerf is wide and the cut face tilts slightly into a V-shaped taper.
- Q. Can plasma cut holes smaller than the plate thickness?
- Holes smaller than the plate thickness are difficult, and forcing them can distort the surrounding area. For example, a 10 mm diameter bolt hole in 30T plate should only be center-marked and drilled later.
Plasma Cutting quote from one drawing
Upload STEP or DWG → instant quote → final quote. Analysis through pricing is automated.
Upload a drawing| TitlePlasma Cutting | Scale1:4 | Unitmm | |
| FormatA4 | Date2026-03-12 | Proj. | Sheet1/1 |
| Dwg No.MAKEIT-PLASMA-CUTTING | Thk12 | RevA | |
